Download New Latest (May) Cisco 600-601 Actual Tests 31-40

By | May 15, 2015

Ensurepass

 

 

QUESTION 31

You are troubleshooting a connectivity problem and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. Which command would you issue to see where the packets stop?

 

A.

router#ping

B.

router#tracert

C.

router#show ip route

D.

router#show cdp neighbors

E.

router#traceroute

 

Answer: E

Explanation:

 

QUESTION 32

The network administrator is using a Windows PC application that is called putty.exe for remote communication to a switch for network troubleshooting. Which two protocols could be used during this communication? (Choose two).

 

A.

SNMP

B.

HTTP

C.

Telnet

D.

RMON

E.

SSH

 

Answer: CE

Explanation:

 

QUESTION 33

What are two symptoms of duplex mismatch? (Choose two.)

 

A.

Ping does not return from one direction versus the other direction.

B.

Communication is slow and locks up.

C.

Speed is seen equally slow in both directions.

D.

The half-duplex side sees frame sequence errors or runt frames.

E.

The full-duplex side sees CRC errors.

 

Answer: BD

Explanation:

 

QUESTION 34

With a Cisco IE 2000 switch, what does a port status LED indicate when it is alternating green and amber?

 

A.

The port is sending or receiving data.

B.

A link is present.

C.

No link is present.

D.

There is a link fault.

E.

The port is not forwarding.

 

Answer: D

Explanation:

 

QUESTION 35

With a Cisco IE 2000 switch, what does a port status LED indicate when it is solid amber?

 

A.

The port is sending or receiving data.

B.

A link is present.

C.

No link is present.

D.

There is a link fault.

E.

The port is not forwarding.

 

Answer: E

Explanation:

 

QUESTION 36

With a Cisco IE 2000 switch, what does a port status LED indicate when it is solid green?

 

A.

The port is sending or receiving data.

B.

A link is present.

C.

No link is present.

D.

There is a link fault.

E.

The port is not forwarding.

 

Answer: B

Explanation:

 

QUESTION 37

You are a called upon to troubleshoot connectivity problems to a network device on a production floor. You have used ping and traceroute to verify that you cannot connect to the device from the management network. The network is 209.165.202.128/27 and the device has been given the IP address 209.165.202.158 and mask 255.255.255.224. You have verified that you can reach the device with your computer connected to the same switch as the device. What could be the cause of this problem?

 

A.

The device is set to the wrong subnet mask.

B.

The device is set to the wrong IP address.

C.

The device has no IP default gateway.

D.

The device is connected to a switchport in the wrong VLAN.

 

Answer: C

Explanation:

 

QUESTION 38

What are two recommended tools or commands that allow you to troubleshoot connectivity between two devices in different IP networks? (Choose two.)

 

A.

show interface status

B.

show spanning-tree

C.

ping

D.

show interfaces gigabitEthernet x/y switchport

E.

traceroute

F.

show interface

 

Answer: CE

Explanation:

 

QUESTION 39

In which two ways could you minimize the impact of monitoring an industrial network? (Choose two.)

 

A.

Send random messages to a device and see what the response is.

B.

Do frequent ping sweeps to industrial devices to check for their proper operations.

C.

Make a copy of all the network traffic and analyze it offline.

D.

Use an industrial-network-grade IDS-IPS system.

 

Answer: CD

Explanation:

 

QUESTION 40

What is the leading cause of fiber-optic link failure?

 

A.

contaminants

B.

crushed fiber

C.

poor testing practices

D.

bad connectors

 

Answer: A

Explanation:

Free VCE & PDF File for Cisco 600-601 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …