Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 151-160

By | April 22, 2015

Ensurepass

 

QUESTION 151

In the implementation of VLSM techniques on a network using a single Class C IP address, which subnet mask is the most efficient for point-to-point serial links?

 

A.        255.255.255.240

B.        255.255.255.254

C.        255.255.255.252

D.        255.255.255.0

E.         255.255.255.248

 

Correct Answer: C

 

 

 

 

 

QUESTION 152

Refer to the exhibit. Host A cannot ping Host B. Assuming routing is properly configured. What could be the cause of this problem?

 

clip_image002

 

A.       Host A is not on the same subnet as its default gateway.

B.       The address of Switch A is a subnet address.

C.       The Fa0/0 interface on Router A is on a subnet that cannot be used.

D.       The serial interfaces of the routers are not on the same subnet.

E.        The Fa0/0 interface on Router B is using a broadcast address.

 

Correct Answer: D

 

 

QUESTION 153

The network administrator is asked to configure 113 point-to-point links. Which IP addressing scheme best defines the address range and subnet mask that meet the requirement and waste the fewest subnet and host addresses?

 

A.       10.10.0.0/18 subnetted with mask 255.255.255.252

B.       10.10.0.0/25 subnetted with mask 255.255.255.252

C.       10.10.0.0/24 subnetted with mask 255.255.255.252

D.       10.10.0.0/23 subnetted with mask 255.255.255.252

E.        10.10.0.0/16 subnetted with mask 255.255.255.252

 

Correct Answer: D

 

 

QUESTION 154

If an Ethernet port on a router was assigned an IP address of 172.1.1.1/20, what is the maximum number of hosts allowed on this subnet?

 

A.        4094

B.        1024

C.        8190

D.        2046

E.         4096

 

Correct Answer: A

 

 

QUESTION 155

Refer to the exhibit. Which address and mask combination a summary of the routes learned by EIGRP?

 

clip_image003

 

A.        192.168.25.0 255.255.255.240

B.        192.168.25.16 255.255.255.252

C.        192.168.25.0 255.255.255.252

D.        192.168.25.28 255.255.255.240

E.         192.168.25.16 255.255.255.240

F.         192.168.25.28 255.255.255.240

 

Correct Answer: E

 

 

QUESTION 156

A network administrator receives an error message while trying to configure the Ethernet interface of a router with IP address 10.24.24.24/29. Which statement explains the reason for it?

 

A.       The address is a broadcast address.

B.       The Ehernet interface is faulty.

C.       VLSM-capable routing protocols must be enable first on the router.

D.       This address is a network address.

 

Correct Answer: D

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 157

Host A pings interface S0/0 on Router3, what will be the TTL value for that ping before it enter Router3?

 

clip_image005

 

A.        253

B.        252

C.        255

D.        254

 

Correct Answer: A

 

 

QUESTION 158

Which two statements are true about the command ip route 172.16.3.0 255.255.255.0 192.168.2.4? (Choose two.)

 

A.       It establishes a static route to the 172.16.3.0 network.

B.       It establishes a static route to the 192.168.2.0 network.

C.       It configures the router to send any traffic for an unknown destination to the 172.16.3.0 network.

D.       It configures the router to send any traffic for an unknown destination out the interface with the address 192.168.2.4.

E.        It uses the default administrative distance.

F.        It is a route that would be used last if other routes to the same destination exist.

 

Correct Answer: AE

 

 

QUESTION 159

Refer to the exhibit. Assume that the routing protocol referenced in each choice below is configured with its default settings and the given routing protocol is running on all the routers. Which two conditional statements accurately state the path that will be chosen between networks 10.1.0.0 and 10.3.2.0 for the routing protocol mentioned? (Choose two.)

 

clip_image007

 

A.       If OSPF is the routing protocol, the path will be from R1 to R3 to R4 to R5.

B.       If OSPF is the routing protocol, the path will be from R1 to R2 to R5.

C.       If OSPF is the routing protocol, the path will be from R1 to R5.

D.       If RIPv2 is the routing protocol, the path will be from R1 to R3 to R4 to R5.

E.        If RIPv2 is the routing protocol, the path will be from R1 to R5.

 

Correct Answer: AE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 160

Refer to the exhibit. Which three statements are true about how router JAX will choose a path to the 10.1.3.0/24 network when different routing protocols are configured? (Choose three.)

 

clip_image008

 

A.       By default, if RIPv2 is the routing protocol, only the path JAX-ORL will be installed into the routing table.

B.       The equal cost paths JAX-CHI-ORL and JAX- NY-ORL will be installed in the routing table if RIPv2 is the routing protocol.

C.       When EIGRP is the routing protocol, only the path JAX-ORL will be installed in the routing table by default.

D.       When EIGRP is the routing protocol, the equal cost paths JAX-CHI-ORL, and JAX-NY-ORL will be installed in the routing table by default.

E.        With EIGRP and OSPF both running on the network with their default configurations, the EIGRP paths will be installed in the routing table.

F.        The OSPF paths will be installed in the routing table, if EIGRP and OSPF are both running on the network with their default configurations.

 

Correct Answer: ADE

 

Free VCE & PDF File for Cisco 100-101 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …