Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 61-70

By | April 22, 2015

Ensurepass

 

QUESTION 61

The command ip route 192.168.100.160 255.255.255.224 192.168.10.2 was issued on a router.

No routing protocols or other static routes are configured on the router. Which statement is true about this command?

 

A.      The interface with IP address 192.168.10.2 is on this router.

B.      The command sets a gateway of last resort for the router.

C.      Packets that are destined for host 192.168.100.160 will be sent to 192.168.10.2.

D.      The command creates a static route for all IP traffic with the source address 192.168.100.160.

 

Correct Answer: C

 

 

QUESTION 62

Which two of these functions do routers perform on packets? (Choose two.)

 

A.      Examine the Layer 2 headers of inbound packets and use that information to determine the next hops for the packets

B.      Update the Layer 2 headers of outbound packets with the MAC addresses of the next hops

C.      Examine the Layer 3 headers of inbound packets and use that information to determine the next hops for the packets

D.      Examine the Layer 3 headers of inbound packets and use that information to determine the complete paths along which the packets will be routed to their ultimate destinations

E.       Update the Layer 3 headers of outbound packets so that the packets are properly directed to valid next hops

F.       Update the Layer 3 headers of outbound packets so that the packets are properly directed to their ultimate destinations

 

Correct Answer: BC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 63

Refer to the exhibit. Which two statements are correct? (Choose two.)

 

clip_image002

 

A.      This is a default route.

B.      Adding the subnet mask is optional for the ip route command.

C.      This will allow any host on the 172.16.1.0 network to reach all known destinations beyond RouterA.

D.      This command is incorrect, it needs to specify the interface, such as s0/0/0 rather than an IP address.

E.       The same command needs to be entered on RouterA so that hosts on the 172.16.1.0 network can reach network 10.0.0.0.

 

Corre
ct Answer: AC

 

 

QUESTION 64

Refer to the exhibit. If CDP is enabled on all devices and interfaces, which devices will appear in the output of a show cdp neighbors command issued from R2?

 

clip_image004

 

A.      R2 and R3

B.      R1 and R3

C.      R3 and S2

D.      R1, S1, S2, and R3

E.       R1, S1, S2, R3, and S3

 

Correct Answer: C

 

 

QUESTION 65

Refer to the exhibit. Th
e two routers have had their startup configurations cleared and have been restarted. At a minimum, what must the administrator do to enable CDP to exchange information between R1 and R2?

 

clip_image006

 

A.      Configure the router with the cdp enable command.

B.      Enter no shutdown commands on the R1 and R2 fa0/1 interfaces.

C.      Configure IP addressing and no shutdown commands on both the R1 and R2 fa0/1 interfaces.

D.      Configure IP addressing and no shutdown commands on either of the R1 or R2 fa0/1

interfaces.

 

Correct Answer: B

 

 

QUESTION 66

Which two commands will display the current IP address and basic Layer 1 and 2 status of an interface? (Choose two.)

 

A.      router#show version

B.      router#show ip interface

C.      router#show protocols

D.      router#show controllers

E.       router#show running-config

 

Correct Answer: CD

 

 

QUESTION 67

An administrator is in the process of changing the configuration of a router. What command will allow the administrator to check the changes that have been made prior to saving the new configuration?

 

A.      Router# show startup-config

B.      Router# show current-config

C.      Router# show running-config

D.      Router# show memory

E.       Router# show flash

F.       Router# show processes

 

Correct Answer: C

 

 

QUESTION 68

On a live network, which commands will verify the operational status of router interfaces?

(Choose two.)

 

A.      Router# show interfaces

B.      Router# show ip protocols

C.      Router# debug interface

D.      Router# show ip interface brief

E.       Router# show start

 

Correct Answer: AD

 

 

QUESTION 69

Which router command will configure an interface with the IP address 10.10.80.1/19?

 

A.      router(config-if)# ip address 10.10.80.1/19

B.      router(config-if)# ip address 10.10.80.1 255.255.0.0

C.      router(config-if)# ip address 10.10.80.1 255.255.255.0

D.      router(config-if)# ip address 10.10.80.1 255.255.224.0

E.       router(config-if)# ip address 10.10.80.1 255.255.240.0

F.       router(config-if)# ip address 10.10.80.1 255.255.255.240

 

Correct Answer: D

 

 

QUESTION 70

Refer to the exhibit. If the resume command is entered after the sequence that is shown in the exhibit, which router prompt will be displayed?

 

clip_image008

 

A.      Router1>

B.      Router1#

C.      Router2>

D.      Router2#

 

Correct Answer: C

 

Free VCE & PDF File for Cisco 100-101 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …