Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 31-40

By | April 22, 2015

Ensurepass

 

QUESTION 31

Which parameter or parameters are used to calculate OSPF cost in Cisco routers?

 

A.      Bandwidth

B.      Bandwidth and Delay

C.      Bandwidth, Delay, and MTU

D.      Bandwidth, MTU, Reliability, Delay, and Load

 

Correct Answer: A

 

 

QUESTION 32

Which statements are true about EIGRP successor routes? (Choose two.)

 

A.      A successor route is used by EIGRP to forward traffic to a destination.

B.      Successor routes are saved in the topology table to be used if the primary route fails.

C.      Successor routes are flagged as ‘active’ in the routing table.

D.      A successor route may be backed up by a feasible successor route.

E.       Successor routes are stored in the neighbor table following the discovery process.

 

Correct Answer: AD

 

 

QUESTION 33

Refer to the exhibit. The network associate is configuring OSPF on the Core router. All the connections to the branches should be participating in OSPF. The link to the ISP should NOT participate in OSPF and should only be advertised as the default route. What set of commands will properly configure the Core router?

 

clip_image002

 

A.      Core(config-router)# default-information originate

Core(config-router)# network 10.0.0.0 0.255.255.255 area 0

Core(config-router)# exit

Core(config)# ip route 0.0.0.0 0.0.0.0 10.10.2.14

 

B.      Core(config-router)# default-information originate

Core(config-router)# network 10.10.2.13 0.0.0.242 area 0

Core(config-router)# exit

Core(config)# ip route 0.0.0.0 0.0.0.0 10.10.2.14

 

C.      Core(config-router)# default-information originate

Core(config-router)# network 10.10.2.16 0.0.0.15 area 0

Core(config-router)# exit

Core(config)# ip route 0.0.0.0 0.0.0.0 10.10.2.14

 

D.      Core(config-router)# default-information originate

Core(config-router)# network 10.10.2.32 0.0.0.31 area 0

Core(config-router)# exit

Core(config)# ip route 0.0.0.0 0.0.0.0 10.10.2.14

 

Correct Answer: C

 

 

QUESTION 34

Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)

 

clip_image004

 

A.      It ensures that data will be forwarded by RouterB.

B.      It provides stability for the OSPF process on RouterB.

C.      It specifies that the router ID for RouterB should be 10.0.0.1.

D.      It decreases the metric for routes that are advertised from RouterB.

E.       It indicates that RouterB should be elected the DR for the LAN.

 

Correct Answer: BC

 

 

QUESTION 35

What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?

 

A.      2

B.
     
4

C.      16

D.      unlimited

 

Correct Answer: B

 

 

QUESTION 36

Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?

 

A.      hop count

B.      administrative distance

C.      link bandwidth

D.      link delay

E.       link cost

 

Correct Answer: B

 

 

QUESTION 37

What are two drawbacks of implementing a link-state routing protocol? (Choose two.)

 

A.      the sequencing and acknowledgment of link-state packets

B.      the requirement for a hierarchical IP addressing scheme for optimal functionality

C.      the high volume of link-state advertisements in a converged network

D.      the high demand on router resources to run the link-state routing algorithm

E.       the large size of the topology table listing all advertised routes in the converged network

 

Correct Answer: BD

 

 

QUESTION 38

Which two are advantages of static routing when compared to dynamic routing? (Choose two.)

 

A.      Configuration complexity decreases as network size increases.

B.      Security increases because only the network administrator may change the routing table.

C.      Route summarization is computed automatically by the router.

D.      Routing tables adapt automatically to topology changes.

E.       An efficient algorithm is used to build routing tables, using automatic updates.

F.       Routing updates are automatically sent to neighbors.

G.      Routing traffic load is reduced when used in stub network links.

 

Correct Answer: BG

 

 

QUESTION 39

A router is running three routing processes: RIP, OSPF, and EIGRP, each configured with default characteristics. Each process learns a route to the same remote network. If there are no static routes to the destination and none of the routes were redistributed, which route will be placed in the IP routing table?

 

A.      the route learned through EIGRP

B.      the route learned through OSPF

C.      the route learned through RIP

D.      the route with the lowest metric

E.       all three routes with the router load balancing

 

Correct Answer: A

QUESTION 40

Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?

 

clip_image006

 

A.      10.1.1.2

B.      10.154.154.1

C.      172.16.5.1

D.      192.168.5.3

 

Correct Answer: C

 

Free VCE & PDF File for Cisco 200-101 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …