Download New Updated (Spring 2015) Cisco 350-001 Actual Tests 81-90

By | April 22, 2015




Refer to the exhibit. You are trying to police down to 100 Mb/s. While testing, you notice that you rarely exceed 70-80 Mb/s. What do you need to change in your MQC configuration to allow for 100 Mb/s speeds?




A.       Change the CIR value from 100 Mb/s to 200 Mb/s.

B.       Change the Bc value to allow for a large enough burst.

C.       Change the QoS queue from default to priority.

D.      Change the exceed-action to transmit.


Correct Answer: B




Which feature would prevent guest users from gaining network access by unplugging an IP phone and connecting a laptop computer?


A.       < /span>IPSec VPN

B.       SSL VPN

C.       port security

D.      port security with statically configured MAC addresses

E.       private VLANs


Correct Answer: D


After applying a new ACL on a device, its CPU utilization rose significantly and many messages starting with “%SEC-6-IPACCESSLOG” appeared on the Syslog server. What can be done to resolve this situation?


A.       Increase memory allocation for ACLs.

B.       Remove all entries from the ACL and use a single permit ip any any statement.

C.       Remove the log keyword from each ACL entry.

D.      Rebo
ot the device after the ACL has been applied.


Correct Answer: C




Refer to the exhibit. Clients that are connected to Fa0/0 of RTA are only allowed to connect to the Internet and networks, but not the networks on Fa1/0, Fa2/0, Fa3/0 and Fa4/0. To achieve this, you have configured an ACL on RTA and applied it on the incoming direction of interface Fa0/0. After you apply this ACL, you learn that some of these networks are still accessible for clients that are connected to the network. What is the correct ACL configuration to solve this issue?




A.       access-list 101 deny ip any access-list 101 permit ip any any

B.       access-list 101 permit ip any access-list 101 deny ip any any

C.       access-list 101 deny ip any access-list 101 permit ip any any

D.      access-list 101 deny ip any access-list 101 permit ip any any


Correct Answer: D





You are the network administrator of a medium-sized company, and users are complaining that they cannot send emails to some organizations. During your troubleshooting, you notice that your DNS MX record is blacklisted by several public blacklist filters. After clearing these listings for your IP address, and assuming that your email server has the right virus protection in place, what are two possible solutions to prevent this from happening in the future? (Choose two.)


A.       Change your Internet provider.

B.       Change your public IP address.

C.       Allow the email server to send traffic only to TCP port 25.

D.      Put your email server in a DMZ.

E.       Use a separate public IP address for your email server only.


Correct Answer: CE




When troubleshooting the issue, you notice the election of a new root bridge with an unknown MAC address. Knowing that all access ports have the PortFast feature enabled, what would be the easiest way to resolve the issue without losing redundant links?


A.       Enable bpduguard globally.

B.       Enable rootguard.

C.       Enable loopguard.

D.      Enable spanning tree.

E.       Enable UDLD.


Correct Answer: A




You are the network administrator of a small Layer 2 network with 50 users. Lately, users have been complaining that the network is very slow. While troubleshooting, you notice that the CAM table of your switch is full, although it supports up to 12, 000 MAC addresses. How can you solve this issue and prevent it from happening in the future?


A.       Upgrade the switches

B.       Configure BPDU guard

C.       Configure VLAN access lists

D.      Configure port security

E.       Configure Dynamic ARP inspection


Correct Answer: D



On a router that is configured with multiple IP SLA probes, which command can be used to manage the CPU load that was created by the periodic probing?


A.       ip sla monitor low-memory

B.       ip sla group schedule

C.       ip sla reaction-trigger

D.      ip sla enable timestamp


Correct Answer: B




Which configuration would make an IP SLA probe use a precedence value of 3?


A.        ip sla 1

icmp-echo tos 12


B.        ip sla 1

icmp-echo tos 96


C.        ip sla 1

icmp-echo precedence 3


D.        ip sla 1

icmp-echo dscp 12


Correct Answer: B




Refer to the exhibit. When would the EEM applet be triggered?




A.       every time that the input packet per second counter is below 10, 000

B.       every time that the input packet per second counter has increased by 1, 000

C.       every time that the input packet per second counter is above 10, 000

D.      every time that the input packet per second counter has decreased by 1, 000


Correct Answer: C


Free VCE & PDF File for Cisco 350-001 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …