Download New Updated (Spring 2015) Cisco 350-050 Actual Tests 131-140

By | April 26, 2015

Ensurepass

 

QUESTION 131

Which two statements about virtual interfaces on a WLC are true? (Choose two.)

 

A.

A virtual interface serves as the redirect address for the web authentication login page.

B.

A virtual interface must have a DNS host name in order to prevent web authentication clients from

getting a security warning on their web browser.

C.

A virtual interface acts as the DHCP server placeholder for wireless clients that obtain their IP address

from a DHCP server.

D.

A virtual interface acts as a RADIUS proxy for wireless clients.

 

Correct Answer: AC

 

 

QUESTION 132

Refer to the exhibit. Which EAP type does the diagram illustrate?

 

clip_image002

 

A.

EAP-TLS

B.

EAP-MD5

C.

PEAP

D.

EAP-GTC

E.

EAP-FAST

F.

LEAP

 

Correct Answer: E

 

 

QUESTION 133

Which statement describes the operation of an access point in Rogue Location Discovery Protocol mode?

 

A.

The AP uses the existing wireless infrastructure in order to scan for rogue APs. Once discovered,

these rogues are added to a local list that includes the rogues’ BSSIDs, MAC addresses, and any

discovered security provisions (WPA, WEP, etc.).

B.

The AP detects a rogue client, and then the network administrator is able to contain both the rogue

AP and the rogue clients. This can be achieved because 802.11 deauthentication packets are sent

to clients that are associated to rogue APs, so threats such as holes are mitigated.

C.

The AP moves to the rogue channel and attempts to connect to the rogue as a client. The AP then

tries to obtain an IP address and forwards a UDP packet to the controller through the rogue.

If the controller receives this packet, the network administrator is notified that a rogue AP has been

discovered on the wired network.

D.

The AP determines whether or not a rogue access point is on a trusted network. It does not provide

RF service of any kind, but rather receives periodic rogue access point reports from the controller,

and sniffs all ARP packets. If it finds a match between an ARP request and a MAC address it receives

from the controller, it generates a rogue access point alert to the controller.

 

Correct Answer: C

 

 

QUESTION 134

Refer to the exhibit. You want to use 3500e APs to setup an indoor mesh deployment. After you change the AP mode, the AP will not rejoin the Cisco WLC. Which debug command was run, according to the exhibit, and why is the AP not rejoining the Cisco WLC?

 

clip_image004

 

A.

debug capwap packet was run, and 3500e APs do not support indoor mesh.

B.

debug pm pki was run, and you must disable VLAN transparent for 3500e indoor mesh deployments.

C.

debug mesh security was run, and the 3500e radio MAC address is not in the local MAC filter list on the

Cisco WLC.

D.

debug ap join was run, and you must disable VLAN transparent for 3500e indoor mesh deployments.

E.

debug capwap events enable was run, and the 3500e Ethernet MAC address is not in the local MAC filter

list on the Cisco WLC.

 

Correct Answer: E

 

 

 

 

QUESTION 135

When you configure channel bonding on your APs by using the 2.4-GHz radio, what is the maximum number of APs that you can place in a given location so that the AP channels do not overlap?

 

A.

One

B.

Two

C.

Three

D.

Threein most of the countries, but 4 (including channel 14) in Japan

 

Correct Answer: A

 

 

QUESTION 136

You calculate that your AP should transmit at 6 dBm to provide appropriate wireless coverage, while still complying with EIRP, with the antennas that you selected. However, the AP is

transmitting at 1 dBm only, even though it is on power level 1. How can you increase the transmitting power?

 

A.

Choose appropriate antennas types.

B.

Decrease the antenna gain that is configured on the Cisco WLC.

C.

Switch to a custom Tx power level and increase the power level.

D.

Disable auto-RF.

E.

Activate 802.11n legacy beamforming on the Cisco WLC.

 

Correct Answer: B

 

 

QUESTION 137

AP A is in AP group ONE and AP B in is AP group TWO. AP group ONE assigns the interface Marketing to the corporate WLAN, whereas AP group TWO assigns the interface Sales to the same WLAN. What happens if a client roams from AP A to AP B while connected to the corporate SSID?

 

A.

No roaming is possible.

B.

The client will reconnect with a new IP address from the Sales subnet.

C.

The client will keep its Marketing subnet IP address, but roaming will not be seamless.

D.

The client will keep its Marketing subnet IP address, and roaming will be seamless if the appropriate

key management is used.

E.

A mobility tunnel will be established between the two APs, and the client will be allowed to keep its

IP address.

 

Correct Answer: D

 

 

QUESTION 138

What does disabling broadcast SSID in the WLAN configuration do?

 

A.

causes beacons to be unicast instead of broadcast

B.

prevents beacons from being sent and allows only probes

C.

allows beacons to be sent but leaves the SSID name field empty

D.

forbids all broadcasts for that SSID

E.

makes the SSID respond only to blank probes

Correct Answer: C

 

 

QUESTION 139

What does RLDP do?

 

A.

allows APs to detect rogues

B.

allows the Cisco MSE or location appliance to calculate the location of rogues

C.

allows APs to determine whether undetected rogue APs or clients are in the area

D.

makes APs stop servicing clients and tries to associate to the unsecured AP, to send special UDP

packet to the Cisco WLC

E.

makes APs try t
o break the security of rogue APs, to allow better containment

 

Correct Answer: D

 

 

QUESTION 140

You are designing a wireless guest anchoring solution for a large company. Forty-five Cisco WLCs running 7.0.116.0 code are deployed in the corporate network. You expect about 3000 devices to use the guest network at any one time. A junior wireless administrator has suggested using a single 4402-12 WLC running 7.0.116.0 as the anchor controller. What is your response?

 

A.

Using a 4402-12 WLC is the best option, based on the design requirements, because it is currently the

least expensive WLC that supports auto-anchoring.

B.

Using a 4402 WLC is not feasible because 4402 WLCs do not support the 7.0 release of code.

C.

A single 4402 WLC supports only 2500 client database entries and therefore does not meet the design

requirements.

D.

A single 4402-12 WLC, regardless of code. supports only 40 simultaneous EoIP tunnels and therefore

does not meet the design requirements.

 

Correct Answer: C

 

Free VCE & PDF File for Cisco 350-050 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …