Download New Updated (Spring 2015) Cisco 642-813 Actual Tests 131-140

By | April 28, 2015






Correct Answer:




















clip_image00642-813 Testing software, Cisco 642-813 PDF, Cisco 642-813 VCE, Latest Cisco 642-813 Dumps, Latest Cisco 642-813 Real Exam, New Updated 642-813 Actual Tests


Correct Answer:






















Correct Answer:






















Correct Answer:
















Correct Answer:




















Refer to the Exhibit.


The information of the question

You will configure FastEthernet ports 0/12 through 0/24 for users who belong to VLAN 20. Also, all VLAN and VTP configurations are to be completed in global configuration mode as VLAN database mode is being deprecated by Cisco. You are required to accomplish the following tasks:


1.         Ensure the switch does not participate in VTP but forwards VTP advertisements received on

trunk ports.

2.         Ensure all non-trunking interfaces (Fa0/1 to Fa0/24) transition immediately to the

forwarding state of Spanning-Tree.

3.         Ensure all FastEthernet interfaces are in a permanent non-trunking mode.

4.         Place FastEthernet interfaces 0/12 through 0/24 in VLAN 20


Correct Answer:

switch# conf t

switch(config)# vtp mode transparent

switch(config)# interface range fa0/1 – 24

switch(config-if-range)# switchport mode access

switch(config-if-range)# spanning-tree portfast

switch(config)# interface range fa0/12 – 24

switch(config-if-range)# switchport access vlan 20

switch(config-if-range)# end

switch# copy running-config startup-config


The headquarter offices for a book retailer are enhancing their wiring closets with Layer3 switches. The new distribution-layer switch has been installed and a new access-layer switch cabled to it. Your task is to configure VTP to share VLAN information from the distribution-layer switch to the access-layer devices. Then, it is necessary to configure interVLAN routing on the distribution layer switch to route traffic between the different VLANs that are configured on the access-layer switches; however, it is not necessary for you to make the specific VLAN port assignments on the access-layer switches. Also, because VLAN database mode is being deprecated by Cisco, all VLAN and VTP configurations are to be completed in the global configuration mode. Please reference the following table for the VTP and VLAN information to be configured:







These are your specific tasks:


1.       Configure the VTP information with the distribution layer switch as the VTP server

2.       Configure the VTP information with the access layer switch as a VTP client

3.       Configure VLANs on the distribution layer switch

4.       Configure inter-VLAN routing on the distribution layer switch

5.       Specific VLAN port assignments will be made as users are added to the access layer switches in the future.

6.       All VLANs and VTP configurations are to completed in the global configuration. To configure the switch click on the host icon that is connected to the switch be way of a serial console cable.


Correct Answer:

DLSwitch# conf t

DLSwitch(config)# vtp mode server

DLSwitch(config)# vtp domain cisco

DLSwitch(config)# vlan 20

DLSwitch(config)# vlan 21

DLSwitch(config)# int vlan 20

DLSwitch(config-if)# ip address

DLSwitch(config-if)# no shutdown

DLSwitch(config-if)# exit

DLSwitch(config)# int vlan 21

DLSwitch(config-if)# ip address

DLSwitch(config-if)# no shutdown

DLSwitch(config-if)# exit

DLSwitch(config)# ip routing

DLSwitch(config)# end

DLSwitch# copy running-config startup-config




Refer to the Exhibit.




Online Incorporated is an internet game provide. The game service network had recently added an additional switch block with multiple VLANs configured. Unfortunately, system administrators neglected to document the spanning-tree topology during configuration. For baseline purpose, you will be required to identify the spanning-tree topology for the switch block. Using the output of “show spanning-tree” command on switch SW-C and the provided physical topology, answer the following questions:

Beware: VLAN number can change.




Question 1

Which spanning Tree Protocol has been implemented on SW-B?


A.        STP/IEEE 802.1D

B.        MSTP/IEEE 802.1s

C.        PVST+

D.        PVRST

E.         None of the above


Correct Answer: C



Question 2

Which bridge ID belongs to SW-B?


A.      24623.000f.34f5.0138

B.      32768.000d.bd03.0380

C.      32768.000d.65db.0102

D.      32769.000d.65db.0102

E.       32874.000d.db03.0380

F.       32815.000d.db03.0380


Correct Answer: A



Question 3

Which port role has interface Fa0/2 of SW-A adopted for VLAN 47?


A.      Root port

B.      Nondesigned port

C.      Designated port

D.      Backup port

E.       Alternate port


Correct Answer: C



Question 4

Which port state is interface Fa0/2 of SW-B in for VLANs 1 and 106?


A.      Listening

B.      Learning

C.      Disabled

D.      Blocking

E.       Forwarding

F.       Discarding


Correct Answer: D



Question 5

Which bridge ID belongs to SW-A?


A.      24623.000f.34f5.0138

B.      32768.000d.bd03.0380