Download New Updated (Spring 2015) Cisco 642-813 Actual Tests 51-60

By | April 28, 2015

Ensurepass

 

QUESTION 51

Refer to the exhibit. You have configured an interface to be an SVI for Layer 3 routing capabilities. Assuming that all VLANs have been correctly configured, what can be determined?

 

clip_image002

 

A.        Interface gigabitethernet0/2 will be excluded from Layer 2 switching and enabled for Layer 3 routing.

B.        The command switchport autostate exclude should be entered in global configuration mode, not subinterface mode, to enable a Layer 2 port to be configured for Layer 3 routing.

C.        The configured port is excluded in the calculation of the status of the SVI.

D.        The interface is missing IP configuration parameters; therefore, it will only function at Layer 2.

 

Correct Answer: C

 

 

QUESTION 52

Refer to the exhibit. Which two statements about this Layer 3 security configuration example are true? (Choose two.)

clip_image004

 

A.        Static IP source binding can be configured only on a routed port.

B.        Source IP and MAC filtering on VLANs 10 and 11 will occur.

C.        DHCP snooping will be enabled automatically on the access VLANs.

D.        IP Source Guard is enabled.

E.         The switch will drop the configured MAC and IP address source bindings and forward all

other traffic.

 

Correct Answer: BD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 53

Refer to the exhibit. Which statement is true?

 

clip_image006

 

A.       Cisco Express Forwarding load balancing has been disabled.

B.       SVI VLAN 30 connects directly to the 10.1.30.0/24 network due to a valid glean adjacency.

C.       VLAN 30 is not operational because no packet or byte counts are indicated.

D.      The IP Cisco Express Forwarding configuration is capable of supporting IPv6.

 

Correct Answer: B

 

 

QUESTION 54

Which statement about the EIGRP routing being performed by the switch is true?

 

clip_image008

 

A.        The EIGRP neighbor table contains 20 neighbors.

B.        EIGRP is running normally and receiving IPv4 routing updates.

C.        EIGRP status cannot be determined. The command show ip eigrp topology would determine

the routing protocol status.

D.        The switch has not established any neighbor relationships. Further network testing and

troubleshooting must be performed to determine the cause of the problem.

 

Correct Answer: D

QUESTION 55

What is the result of entering the command spanning-tree loopguard default?

 

A.       The command enables loop guard and root guard.

B.       The command changes the status of loop guard from the default of disabled to enabled.

C.       The command activates loop guard on point-to-multipoint links in the switched network.

D.      The command disables EtherChannel guard.

 

Correct Answer: B

 

 

QUESTION 56

What does the interface subcommand switchport voice vlan 222 indicate?

 

A.       The port is configured for both data and voice traffic.

B.       The port is fully dedicated to forwarding voice traffic.

C.       The port operates as an FXS telephony port.

D.      Voice traffic is directed to VLAN 222.

 

Correct Answer: A

 

 

QUESTION 57

When you create a network implementation for a VLAN solution, what is one procedure that you should include in your plan?

 

A.       Perform an incremental implementation of components.

B.       Implement the entire solution and then test end-to-end to make sure that it is performing as

designed.

C.       Implement trunking of all VLANs to ensure that traffic is crossing the network as needed

before performing any pruning of VLANs.

D.       Test the solution on the production network in off hours.

 

Correct Answer: A

 

 

QUESTION 58

You have just created a new VLAN on your network. What is one step that you should include in your VLAN-based implementation and verification plan?

 

A.       Verify that different native VLANs exist between two switches for security purposes.

B.       Verify that the VLAN was added on all switches with the use of the show vlan command.

C.       Verify that the switch is configured to allow for trunking on the switch ports.

D.      Verify that each switch port has the correct IP address space assigned to it for the new VLAN.

Correct Answer: B

 

 

QUESTION 59

Which two statements describe a routed switch port on a multilayer switch? (Choose two.)

 

A.       Layer 2 switching and Layer 3 routing are mutually supported.

B.       The port is not associated with any VLAN.

C.       The routed switch port supports VLAN subinterfaces.

D.      The routed switch port is used when a switch has only one port per VLAN or subnet.

E.       The routed switch port ensures that STP remains in the forwarding state.

 

Correct Answer: BD

 

 

QUESTION 60

Which two statements correctly describe VTP? (Choose two.)

 

A.       Transparent mode always has a configuration revision number of 0.

B.       Transparent mode cannot modify a VLAN database.

C.       Client mode cannot forward received VTP advertisements.

D.      Client mode synchronizes its VLAN database from VTP advertisements.

E.       Server mode can synchronize across VTP domains.

 

Correct Answer: AD

 

Free VCE & PDF File for Cisco 642-813 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …