Download New Updated (Spring 2015) Cisco 642-832 Actual Tests 1-10

By | April 28, 2015

Ensurepass

 

QUESTION 1

The following commands are issued on a Cisco Router:

 

Router(configuration)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1

Router(configuration)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1

Router(configuration)#exit

Router#debug ip packet 199

 

What will the debug output on the console show?

 

A.       All IP packets passing through the router

B.       Only IP packets with the source address of 10.1.1.1

C.       All IP packets from 10.1.1.1 to 172.16.1.1

D.      All IP packets between 10.1.1.1 and 172.16.1.1

 

Correct Answer: D

 

 

QUESTION 2

What level of logging is enabled on a Router where the following logs are screen?

 

%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

 

A.       alerts

B.       critical

C.       errors

D.      notifications

 

Correct Answer: D

 

 

QUESTION 3

You have the followings commands on your Cisco Router:

 

ip ftp username admin

ip ftp password backup

 

You have been asked to switch from FTP to HTTP. Which two commands will you use to replace the existing commands?

 

A.       ip http username admin

B.       ip http client username admin

C.       ip http password backup

D.      ip http client password backup

E.       ip http server username admin

F.        ip http server password backup

 

Correct Answer: BD

 

 

QUESTION 4

You have 2 NTP servers in your network – 10.1.1.1 and 10.1.1.2. You want to configurationure a Cisco router to use 10.1.1.2 as its NTP server before falling back to 10.1.1.1. Which commands will you use to configurationure the router?

 

A.  ntp server 10.1.1.1

    ntp server 10.1.1.2

 

B.  ntp server 10.1.1.1

    ntp server 10.1.1.2 primary

 

C.  ntp server 10.1.1.1

    ntp server 10.1.1.2 prefer

 

D.  ntp server 10.1.1.1 fallback

    ntp server 10.1.1.2

 

Correct Answer: C

 

 

QUESTION 5

The following command is issued on a Cisco Router:

 

Router(configuration)#logging console warnings

 

Which alerts will be seen on the console?

 

A.       Warnings only

B.       debugging, informational, notifications, warnings

C.       warnings, errors, critical, alerts, emergencies

D.      notifications, warnings, errors

E.       warnings, errors, critical, alerts

 

Correct Answer: C

 

 

 

QUESTION 6

Which two of the following options are categories of Network Maintenance tasks?

 

A.       Firefighting

B.       Interrupt-driven

C.       Policy-based

D.      Structured

E.       Foundational

 

Correct Answer: BD

 

 

QUESTION 7

You enabled CDP on two Cisco Routers which are connected to each other. The Line and Protocol status for the interfaces on both routers show as UP but the routers do not see each other a CDP neighbors. Which layer of the OSI model does the problem most likely exist?

 

A.       Physical

B.       Session

C.       Application

D.      Data-Link

E.       Network

 

Correct Answer: D

 

 

QUESTION 8

FCAPS is a network maintenance model defined by ISO. It stands for which of the following?

 

A.       Fault Management

B.       Action Management

C.       Configuration Management

D.      Protocol Management

E.       Security Management

 

Correct Answer: ACE

 

 

QUESTION 9

Which three management categories are contained in the FCAPS network maintenance model? (Choose three.)

 

A.      Config

B.      Fault

C.      Storage

D.      Accounting

E.       Redundancy

F.       Telecommunications

 

Correct Answer: ABD

 

 

QUESTION 10

What is the result of configuring the logging console warning command?

 

A.      Messages with a severity level of 4 and higher will be logged to all available TTY lines.

B.      Only warning messages will be logged on the console.

C.      Warning, error, critical, and informational messages will be logged on the console.

D.      Warning, critical, alert, and emergency messages will be logged on the console.

E.       The logging console warning command needs to be followed in the configuration with logging buffered byte size to specify the message buffer size for the console.

 

Correct Answer: D

 

Free VCE & PDF File for Cisco 642-832 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …