Download New Updated (Spring 2015) Cisco 642-902 Actual Tests 1-10

By | April 28, 2015

Ensurepass

 

QUESTION 1

In this question you need to redistribute between OSPF and EIGRP such that 172.16.100.1 is reachable from router R1.

 

clip_image002

 

R2 is an ASBR for EIGRP 100 and OSPF AREA 24

R3 is an ASBR for EIGRP 100 and OSPF AREA 34

Note: There are TWO separate areas on TWO separate ASBRS thus you need to do redistribution on R2 and R3

R1 is ONLY in EIGRP 100, and is THE ONLY router you can ping from. R4 has a loopback interface that must be pinged from R1.

R4 is running OSPF and has redundant links to EIGRP network over R3 router.

Note: You should ping from R1 to 172.16.100.1 network to make sure everything is working correctly.

 

Correct Answer:

First we need to find out 5 K-Values used for EIGRP (Bandwidth, Delay, Reliability, Load, MTU) of the s0/0/0 interface (the interface of R2 connected to R4) for redistribution:

 

R2#show interface s0/0/0

 

Write down these 5 parameters, notice that we have to divide the Delay by 10 because its metric unit is tens of microsecond. For example, we get Bandwidth=1544 Kbit, Delay=20000 us, Reliability=255, Load=1, MTU=1500 bytes then we would redistribute as follows:

 

R2#config terminal

R2(config)#router ospf 1

R2(config-router)# redistribute eigrp 100 metric-type 1 subnets

R2(config-router)#exit

R2(config-router)#router eigrp 100

R2(config-router)#redistribute ospf 1 metric 1544 2000 255 1 1500

 

(Notice: In fact, these parameters are just used for reference and we can use other parameters with no problem. Also, a candidate said that the simulator didn’t accept the Bandwidth of 1544; in that case, we can use a lower value, like 128.)

If the delay is 20000us then we need to divide it by 10, that is 20000 / 10 = 2000)

For R3 we use the show interface fa0/0 to get 5 parameters too

 

R3#show interface fa0/0

 

For example we get Bandwidth=10000 Kbit, Delay=1000 us, Reliability=255, Load=1, MTU=1500 bytes

 

R3#config terminal

R3(config)#router ospf 1

R3(config-router)#redistribute eigrp 100 metric-type 1 subnets

R3(config)#exit

R3(config-router)#router eigrp 100

R3(config-router)#redistribute ospf 1 metric 10000 100 255 1 1500

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 2

Company Acan has two links which can take it to the Internet. The company policy demands that you use web traffic to be forwarded only to Frame Relay link and other traffic can go through any links that are available. Use BGP attributes to solve the requested action.

 

clip_image004

 

Correct Answer:

1) Create an Access list that catches the HTTP traffic:

 

BorderRouter#access-list 101 permit tcp any any eq www

 

Note that the server was not directly connected to the Border Router. There were a lot of EIGRP routes on it. In the real exam you do not know the exact IP address of the server in the EIGRP network so we have to use the source as “any” to catch all the source addresses.

 

2) Route map that sets the next hop address to be ISP1 and permits the rest of the traffic:

 

BorderRouter(config)#route-map pbr permit 10

BorderRouter(config-route-map)#match ip address 101

BorderRouter(config-route-map)#set ip next-hop 10.1.101.1

BorderRouter(config-route-map)#exit

BorderRouter(config)#route-map pbr permit 20

 

(Notice: the route-map pbr permit 20 line allows other traffic than HTTP to be routed. Otherwise, other traffic will be dropped)

 

3) Apply the route-map on the interface to the server in the EIGRP Network:

 

BorderRouter(config-route-map)#exit

BorderRouter(config)#int fa0/0

BorderRouter(config-if)#ip policy route-map pbr

BorderRouter(config-if)#exit

BorderRouter(config)#exit

 

4) There is a “Host for Testing”, click on this host to open a box in which there is a button named “Generate HTTP traffic”. Click on this button to generate some packets for HTTP traffic. Jump back to the BorderRouter and type the command “show route-map”.

 

BorderRouter#show route-map

 

In the output you will see the line “Policy routing matches: 9 packets…”. It means that the route- map we configured is working properly.

 

 

QUESTION 3

By increasing the first distant office, JS manufactures has extended their business. They configured the remote office router (R3) from which they can reach all Corporate subnets. In order to raise network stableness and lower the memory usage and CPU utilization to R3, JS manufactures makes use of route summarization together with the EIGRP Stub Routing feature. Another network engineer is responsible for the implementing of this solution. However, in the process of configuring EIGRP stub routing connectivity with the remote network devices off of R3 has been missing.

 

clip_image005

 

Presently JS has configured EIGRP on all routers in the network R2, R3, and R4. Your duty is to find and solve the connectivity failure problem with the remote office router R3. You should then configure route summarization only to the distant office router R3 to complete the task after the problem has been solved. The success of pings from R4 to the R3 LAN interface proves that the fault has been corrected and the R3.

IP routing table only contains two 10.0.0.0 subnets.

 

Correct Answer:

Use the show runningconfig command on router R3

clip_image006

 

Notice that R3 is configured as a stub receive-only router. The receive-only keyword will restrict the router from sharing any of its routes with any other router in that EIGRP autonomous system. This keyword will also prevent any type of route from being sent. Therefore we will remove this command and replace it with the eigrp stub command:

 

R3#configure terminal

R3(config)#router eigrp 123

R3(config-router)#no eigrp stub receive-only

R3(config-router)#eigrp stub

R3(config-router)#end

 

Now R3 will send updates containing its connected and summary routes to other routers. Notice that the eigrp stub command equals to the eigrp stub connected summary because the connected and summary options are enabled by default. Next we will configure router R3 so that it has only 2 subnets of 10.0.0.0 network. Use the show ip route command on R3 to view its routing table R3#show ip route

clip_image007

 

Because we want the routing table of R3 only have 2 subnets so we have to summary sub- networks at the interface which is connected with R3, the s0/0 interface of R4. There is one interesting thing about the output of the show ip route shown above. The 10.2.3.0 /24, which is a directly connected network of R3. We can’t get rid of it in the routing table no matter what technique we use to summary the networks. Therefore, to make the routing table of R3 has only 2 subnets we have to summarize the other subnets into one subnet. In conclusion, we will use the ip summary-address eigrp 123 10.0.0.0 255.0.0.0 at the interface s0/0 of R4 to summary.

 

R4>enable

R4#configure terminal

R4(config)#interface s0/0

R4(config-if)#ip summary-address eigrp 123 10.0.0.0 255.0.0.0

 

clip_image008

Now we jump back to R3 and use the show ip route command to verify the effect, the output is shown below: (But please notice that the ip addresses and the subnet masks in your real exam might be different so you might use different ones to solve this question) Just for your information, notice that if you use another network than 10.0.0.0/8 to summary, for example, if you use the command ip summary-address eigrp 123 10.2.0.0 255.255.0.0 you will leave a /16 network in the output of the show ip route command.

 

clip_image009

 

But in your real exam, if you don’t see the line “10.0.0.0/8 is a summary …Null0” then you can summary using the network 10.2.0.0/16. This summarization is better because all the pings can work well. Finally don’t forget to use the copy running-config startup-config command on routers R3 and R4 to save the configurations.

 

R4(config-if)#end

R4#copy running-config startup-config

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 4

OSPF is configured on routers Amani and Lynaic. Amani’s S0/0 interface and Lynaic’s S0/1 interface are in Area 0. Lynaic’s Loopback0 interface is in Area 2.

 

clip_image010

 

Your task is to configure the following:

Portland’s S0/0 interface in Area 1

Amani’s S0/1 interface in Area 1

 

Use the appropriate mask such that ONLY Portland’s S0/0 and Amnani’s S0/1 could be in Area 1. Area 1 should not receive any external or inter-area routes (except the default route).

 

Correct Answer:

First, we configure Portland’s S0/0 interface so that it belongs to Area 1. So, we have to find out which subnetwork the IP address 192.168.4.5/30 (the IP of interface S0/0 of Portland) belongs to. This address belongs to a subnetwork which has:

 

Increment: 4 (/30 = 255.255.255.252 or 1111 1111.1111 1111.1111 1111.1111 1100)

Network address: 192.168.4.4 (because 4 = 4 * 1 and 4 < 5)

Broadcast address: 192.168.4.7 (because 7 = 4 + 4 – 1) (It is not necessary to find out the broadcast address but we should know it)

The question requires that only Portland’s S0/0 and Amani’s S0/1 could be in Area 1, therefore we must use a wildcard of 0.0.0.3 (this wildcard is equivalent with a subnet mask of /30) so that there are only 2 IP addresses can participate in area 1 (they are 192.168.4.5 & 192.168.4.6). The full command we use here is network 192.168.4.4 0.0.0.3 area 1 The question also requires that “Area 1 should not receive any external or inter-area routes (except the default route)”. Recall that if we don’t want the router to receive external routes, we have to stop LSA Type 5. And if we don’t want to receive inter-area routes, we have to stop LSA Type 3 and Type 4. Therefore we have to configure area 1 as a totally stubby area. For your information, here is the definition of a totally stubby areA. “Totally stubb area – This area does not accept summary LSAs from other areas (types 3 or 4) or external summary LSAs (Type 5). Types 3,4 and 5 LSAs are replaced by the Area Border Router(ABR) with a default router. Totally stubby areas protect internal routers by minimizing the routing table and summarizing everything outside the area with a default route.” (CCNP BSCI Official Exam Certification Guide, Fourth Edition) In conclusion, we have to configure area 1 as a totally stubby area. We do that by configuring Portland as stub and configuring Amani (ABR router) as a stub + “no-summary”suffix. + Configure Portland router as a stub:

Portland#configure terminal

Portland(config)#router ospf 1

 

Allow network 192.168.4.4/30 to join Area 1, notice that you have to convert subnet mask into wildcard mask:

Portland(config-router)#network 192.168.4.4 0.0.0.3 area 1

 

Configure Portland as a stub:

Portland(config-router)#area 1 stub

Portland(config-router)#end

Portland#copy running-config startup-config

 

+ Configure Amani router as a “totally stub”:

Amani#configure terminal

Amani(config)#router ospf 1

Amani(config-router)#network 192.168.4.4 0.0.0.3 area 1

 

Make area 1 become a totally stubby area, notice that we can only use this command on ABR router:

Amani(config-router)#area 1 stub no-summary

Amani(config-router)#end

Amani#copy running-config startup-config

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 5

Acme is a small export company that has an existing enterprise network that is running IPv6 OSPFv3. Currently OSPF is configured on all routers. However, R4’s loopback address (FEC0:4:4) cannot be seen in R1’s IPv6 routing table. You are tasked with identifying the cause of this fault and implementing the needed corrective actions that uses OSPF features and does no change the current area assignments. You will know that you have corrected the fault when R4’s loopback address (FEC0:4:4) can ping from R1 to R4 loopback address.

 

clip_image012

 

Correct Answer:

To troubleshoot the problem, first issue the show running-config on all of 4 routers. Pay more attention to the outputs of routers R2 and R3 The output of the “show running-config” command of R2:

 

clip_image013

 

The output of the “show running-config” command of R3:

 

clip_image014

 

We knew that all areas in an Open Shortest Path First (OSPF) autonomous system must be physically connected to the backbone area (Area 0). In some cases, where this is not possible, we can use a virtual link to connect to the backbone through a non-backbone area. The area through which you configure the virtual link is known as a transit area. In this case, the area 11 will become the transit area. Therefore, routers R2 and R3 must be configured with the area <area id> virtual- link <neighbor router-id>command. + Configure virtual link on R2 (from the first output above, we learned that the OSPF process ID of R2 is 1):

 

R2>enable

R2#configure terminal

R2(config)#ipv6 router ospf 1

R2(config-rtr)#area 11 virtual-link 3.3.3.3

 

Save the configuration:

R2(config-rtr)#end

R2#copy running-config startup-config

 

(Notice that we have to use neighbor router-id 3.3.3.3, not R2’s router-id 2.2.2.2) + Configure virtual link on R3 (from the second output above, we learned that the OSPF process ID of R3 is 1 and we have to disable the wrong configuration of “area 54 virtual-link 4.4.4.4”):

 

R3>enable

R3#configure terminal

R3(config)#ipv6 router ospf 1

R3(config-rtr)#no area 54 virtual-link 4.4.4.4

R3(config-rtr)#area 11 virtual-link 2.2.2.2

 

Save the configuration:

R3(config-rtr)#end

R3#copy running-config startup-config

 

You should check the configuration of R4, too.

R4(config)#ipv6 router ospf 1

R4(config-router)#no area 54 virtual-link 3.3.3.3

R4(config-router)#end

After finishing the configuration doesn’t forget to ping between R1 and R4 to make sure they work well! NotE. If you want to check the routing information, use the show ipv6 route command, not “show ip route”.

 

 

QUESTION 6

clip_image016

clip_image018

 

Correct Answer:

On router R2:

Config t

Router ospf 1

Redistribute eigrp 100 metric 100 subnets

Router eigrp 100

Redistribute ospf 1 metric 100000 10 200 10 1500

Then from R1 you should be able to ping 172.16.1.100

 

QUESTION 7

The company and the company network have both been growing rapidly. Multiple adds, moves and changes have been applied to the network. Your boss has asked you to troubleshoot a recent OSPF synchronization problem that has arisen. There have been synchronization problems at separate locations in the OSPF area 0. There have been reported link failures during the rapid growth of the company network. You are required to resolve the OSPF problem. OSPF must be able to converge when the network changes.

 

clip_image020

 

Examine the following excerpt from the “show ip ospf” command on D1:

clip_image021

 

Based on the information shown above, what is most likely causing the different missing routes throughout the network?

 

A.       Area 16 is configured with authentication.

B.       Area 16 has been configured to use the same interfaces as Area 0.

C.       Area 0 and Area 32 have been configured with mismatched LSA numbers.

D.      Area 16 has been configured as a total stub network

E.       Area 16 has been configured as a stub network

F.        Area 0 is discontiguous.

G.      None of the above

 

Correct Answer: F

 

 

 

 

 

 

 

 

 

 

QUESTION 8

The company and the company network have both been growing rapidly. Multiple adds, moves and changes have been applied to the network. Your boss has asked you to troubleshoot a recent OSPF synchronization problem that has arisen. There have been synchronization problems at separate locations in the OSPF area 0. There have been reported link failures during the rapid growth of the company network. You are required to resolve the OSPF problem. OSPF must be able to converge when the network changes.

 

clip_image023

 

Which configuration command on D1 (with a similar command on D2) will provide an immediate solution to the missing route problem?

 

A.       no area 16 stub

B.       no area 16 authentication message-digest

C.       area 16 virtual-link 8.187.175.82

D.      area 16 virtual-link 172.16.4.2

E.       no area 16 stub no-summary

F.        network 172.16.0.0.0.0.255.255 area 16

G.      None of the above< /p>

 

Correct Answer: C

 

 

 

 

 

QUESTION 9

The company and the company network have both been growing rapidly. Multiple adds, moves and changes have been applied to the network. Your boss has asked you to troubleshoot a recent OSPF synchronization problem that has arisen. There have been synchronization problems at separate locations in the OSPF area 0. There have been reported link failures during the rapid growth of the company network. You are required to resolve the OSPF problem. OSPF must be able to converge when the network changes.

 

clip_image025

 

The log of d1 reports the following:

clip_image027

 

This event was anticipated due to maintenance; however, it resulted in excessive lost routes. Which route should be the only one removed from the routing tables of the routers?

 

A.       8.187.175.82/32

B.       10.138.43.0/30

C.       10.206.180.0/30

D.      4.249.113.59/32

E.       10.201.0.0/30

F.        None of the above

 

Correct Answer: E

QUESTION 10

The company and the company network have both been growing rapidly. Multiple adds, moves and changes have been applied to the network. Your boss has asked you to troubleshoot a recent OSPF synchronization problem that has arisen. There have been synchronization problems at separate locations in the OSPF area 0. There have been reported link failures during the rapid growth of the company network. You are required to resolve the OSPF problem. OSPF must be able to converge when the network changes.

 

clip_image029

 

The R2 router has lost connectivity to R1. The following is R1s current route table:

 

clip_image030

 

Which expected route is missing from R1`s route table based on the topology during the maintenance period?

 

A.       O 172.16.0.0 [110/2] via 10.138.43.1, 00:00:09, FastEthernet0/0

B.       O IA 9.152.105.122 [110/3] via 10.138.43.1, 00:00:09, FastEthernet0/0

C.       O IA 10.138.0.0 [110/3] via 10.138.43.1, 00:00:09, FastEthernet0/0

D.      O IA 10.249.0.0 [110/2] via 10.138.43.1, 00:00:09, FastEthernet0/0

E.       O IA 4.249.113.59 [110/2] via 10.138.43.1, 00:00:09, FastEthernet0/0

F.        O 8.187.175.82 [110/3] via 10.138.43.1, 00:00:09, FastEthernet0/0

G.      O 10.206.180.0/30 [110/3] via 10.138.43.1, 00:00:09, FastEthernet0/0

 

Correct Answer: F

 

Free VCE & PDF File for Cisco 642-902 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …