Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 Aug Cisco Official New Released 300-470
100% Free Download! 100% Pass Guaranteed!
Implementing and Maintaining Cisco Technologies Using IOS XR
Question No: 21
What is the correct command to copy the contents of the harddisk:/showtech folder to an FTP server?
-
copy harddisk:/showtech location 0/RSP0/CPU0 ftp:
-
copy harddisk:/showtech ftp:
-
copy /recurse harddisk:/showtech location 0/RSP0/CPU0 ftp:
-
copy /recurse harddisk:/showtech ftp:
-
copy ftp: harddisk:/showtech
Answer: C
Question No: 22
What are the two commands to show all log entries except BGP or configuration-related ones? (Choose two.)
-
show log | excl [BGP,CONFIG]
-
show log | excl BGP | excl CONFIG
-
show log | excl (BGP,CONFIG)
-
show log | excl quot;BGP|CONFIGquot;
Answer: B,D
Question No: 23
Which Cisco IOS XR only command will show the status of IPv4 interfaces that have been configured under the OSPF process?
-
show ospf interface
-
show ipv4 ospf interface
-
show ip ospf interface
-
show ospf interface all
-
show ospfv3 interface
-
show ospf address-family
Answer: A
Question No: 24
Which command should be used to view only the running configuration of OSPF in Cisco IOS XR Software?
-
show router ospf
-
show run router ospf
-
show configuration ospf
-
show ospf configuration | running-config
-
show ospf process
Answer: B
Question No: 25
Which is-is router interface configuration command will configure the authentication password for IS-IS Hello (IIH) messages without actually sending the password with the IIH over the network?
-
hello-password text clear secretkey
-
hello-password hmac-md5 clear secretkey
-
hello-password text encrypted secretkey
-
hello-password hmac-md5 encrypted secretkey
Answer: B
Question No: 26
What is the correct procedure to associate a VRF to a static route?
-
configure the VRF under the interface
-
specify the VRF under quot;router staticquot; in configuration mode
-
define the VRF in the global configuration
-
specify the VRF in the route global configuration command
Answer: B
Question No: 27
What is the correct Cisco IOS XR command to configure an autonomous system number 1000 for BGP and to support IPv4, IPv6, and unicast routing?
-
router bgp 1000 address-family ipv4 unicast
!
address-family ipv6 unicast
!
!
-
router bgp 1000
neighbor 1.1.1.1 remote-as 2000 address-family ipv4 unicast
!
address-family ipv6 unicast
!
!
-
router bgp 1000
address-family vpnv4 unicast
!
address-family vpnv6 unicast
!
!
-
router bgp 1000
neighbor 1.1.1.1 remote-as 2000 address-family vpnv4 unicast
!
address-family vpnv6 unicast
!
!
Answer: A
Question No: 28
Which Cisco IOS XR show command is used to display the IPv4 BGP table?
-
show bgp
-
show bgp summary
-
show bgp neighbors
-
show route bgp
-
show bgp vpnv4
-
show bgp table
Answer: A
Question No: 29
Which of the following configurations adds a community to routes that are matched on AS criteria?
-
route-policy policy1 if as-path in set1 then
set community (356:1000) endif
end-policy
-
route-policy policy1
if community in set1 then
set community (356:1000) additive endif
end-policy
-
route-policy policy1 if as-path in set1 then
set community (356:1000) additive endif
end-policy
-
route-policy policy1
if as-path neighbor-is set1 then set community (356:1000) additive endif
end-policy
Answer: C
Question No: 30
Which three commands can verify that the route-policy shown below and applied inbound on the BGP neighbor is working as expected for prefix 2.0.0.0/8?
(Choose three.)
-
show bgp 2.0.0.0 | include 356:1000
-
show bgp | include 2.0.0.0
-
show bgp community 356:1000 | include 2.0.0.0
-
show bgp 2.0.0.0
Answer: A,C,D
100% Dumps4cert Free Download!
–300-470 PDF
100% Dumps4cert Pass Guaranteed!
–300-470 Dumps
Dumps4cert | ExamCollection | Testking | |
---|---|---|---|
Lowest Price Guarantee | Yes | No | No |
Up-to-Dated | Yes | No | No |
Real Questions | Yes | No | No |
Explanation | Yes | No | No |
PDF VCE | Yes | No | No |
Free VCE Simulator | Yes | No | No |
Instant Download | Yes | No | No |