[Free] 2018(Jan) EnsurePass Pass4sure Cisco 300-080 Dumps with VCE and PDF 51-60

By | January 29, 2018

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Cisco Official New Released 300-080
100% Free Download! 100% Pass Guaranteed!

Troubleshooting Cisco IP Telephony amp; Video v1.0

Question No: 51

In Cisco Unified Communications Manager, what is the default maximum number of learned patterns for the call control discovery feature parameter?

A. 5000

B. 10000

C. 20000

D. 500

E. 50000

Answer: C

Question No: 52

Users on your network report fast busy signals when they attempt to place calls. While troubleshooting, you verify that the codecs are configured correctly and determine that the network carries up to 200 concurrent calls at different times of the day. Which two actions correct the problem? (Choose two)

  1. Add more Cisco Unified Communications Managers to the cluster.

  2. Add more DSPs to the NM-HD

  3. Increase the number of sessions to the maximum allowed by system resources.

  4. Implement an SRST-CMF gateway to improve resource allocation.

  5. Add a Cisco Catalyst switch to the environment to increase port density

  6. Bind the network PRIs to add additional bandwidth

Answer: C,F

Question No: 53

A Cisco TelePresence SX80 Dial is registered on Cisco Unified Communications Manager is calling a registered H.323 endpoint that is registered to a Cisco VCS Control within the same campus. The call is placed using 6 Mb, however only a 1 Mb call is set up. Where can you find two possible causes for this issue? (Choose two)

  1. The Cisco TelePiesence SX80. which needs an option key to call over 2 Mb. which also enables multisite calls

  2. in the Region settings in Cisco Unified Communications Manager

  3. bandwidth settings in the SIP trunk profile

  4. legacy telepresence systems that are registered to the Cisco VCS Control and can only do 1 Mb towards a Cisco Unified Communications Manager system

  5. a link and pipe configuration on the VCS to Osco Unified Communications Manager subzone

  6. in the subzone settings of the registered H 323 endpoint

Answer: C

Question No: 54

Cisco TelePresence System EX90-A and EX90-B are in a call. EX90-A tries to call EX90-

C. When the call is dialed, EX90-B is put on hold. EX90-A and EX90-C are connected, but there is no merge button on the touch panel. What is causing this issue?

  1. The multisite option key is missing.

  2. The multisite configuration is missing.

  3. The conference option key is missing.

  4. The conference configuration is missing.

  5. CiscoTelePresence systems cannot make multipoint calls without a Cisco TelePresence Server.

  6. The multipoint option key is missing.

Answer: A

Question No: 55

A user is dialing an external PSTN number with a prefix of 01 from a Cisco TelePresence SX10 Quick Set in a Cisco VCS environment. In the past, the Cisco VCS and the ISDN gateway were correctly configured with a prefix of 01, but the calls are now failing. What are three possible causes? (Choose three.)

  1. The Cisco VCS Control is down.

  2. The interworking setting is turned off.

  3. The audio feature in the Cisco TelePresence SX10 is turned off.

  4. The SIP trunk is not configured on the gateway.

  5. 01 is not a valid prefix.

  6. ISDN is not enabled on the Cisco TelePresence SX10.

  7. The Cisco TelePresence SX10 is not registered to the Cisco VCS Control.

  8. The Cisco TelePresence SX10 is not registered to the Cisco Express C.

Answer: A,B,G

Question No: 56

Which Cisco Unified Communications Manager troubleshooting tool can be used to determine the digit manipulation path a call takes within the Cisco Unified Communications Manager system from the perspective of a specific directory number, without having the actual device at hand?

  1. Cisco Unified Communications Manager Serviceability

  2. Cisco Unified Communications Manager Dialed Number Analyzer

  3. Cisco Unified Communications Manager Real Time Monitoring Tool

  4. Cisco Unified Syslog Viewer

  5. Cisco IOS debugs

Answer: B

Question No: 57

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

Which Cisco Unified Communications Manager trace file level should be selected when enabling traces to send to Cisco TAC for analysis?

  1. State Transition

  2. Arbitrary

  3. Significant

  4. Error

  5. Detailed

  6. Special

Answer: E

Question No: 58

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

When the user tried to configure the command maximum sessions 5 under the dspfarm profile 1, the error shown in the exhibit was reported. Which course of action will resolve this issue?

  1. The maximum conference-participants value must be configured gt;0.

  2. Ensure that the conference bridge is not registered in Cisco Unified Communications Manager.

  3. The command dsp services dspfarm must be configured under the voice-card configuration.

  4. Configure the dspfarm all command under the voice card.

Answer: C

Question No: 59

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

Which course of action will resolve the Mobile Connect issues that are shown in the exhibit?

  1. Configure the Mobility softkey on the phone.

  2. Enable the user for Cisco Mobile Connect.

  3. Make the user an owner of the phone device in the phone device configuration page.

  4. Enable the device mobility mode on the phone since it is disabled.

Answer: C

Question No: 60

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

How many high-complexity transcoding sessions can this Cisco ISR G2 support?

  1. 21

  2. 14

  3. 60

  4. 15

Answer: B

100% Ensurepass Free Download!
Download Free Demo:300-080 Demo PDF
100% Ensurepass Free Guaranteed!
300-080 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.