[Free] 2018(Jan) EnsurePass Pass4sure Cisco 300-080 Dumps with VCE and PDF 71-80

By | January 29, 2018
0 Comment

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Cisco Official New Released 300-080
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/300-080.html

Troubleshooting Cisco IP Telephony amp; Video v1.0

Question No: 71

When the command utils dbreplication status is executed on the Cisco Unified Communications Manager CLI, which step should be taken next to check the database replication status?

  1. View the activelog file.

  2. Run the same command on all nodes of the cluster.

  3. Restart the Cisco CallManager service.

  4. The command utils dbreplication runtimestate must be run on the publisher.

  5. The command utils dbreplication runtimestate must be run on the subscriber.

Answer: A

Question No: 72

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

A roaming device retains its home location device pool settings, even though all configuration settings are in place. What is causing this issue?

  1. The device mobility group settings are incorrect.

  2. The device mobility mode service parameter is set to Off.

  3. The device mobility mode service parameter is set to True.

  4. The device mobility information entry matches the device IP address.

Answer: B

Question No: 73

Two Cisco DX80 collaboration endpoints that support high-definition video are registered to a Cisco Unified Communications Manager in a single-site deployment model. However, the video that is displayed is pixelated and appears as sub-HD. To enable the Cisco DX80s to make high-definition video calls, which configuration option do you check?

  1. Check the configuration in the Cisco DX80 settings menu, and enable high-definition video.

  2. Check the Maximum Session Bit Rate for Video Calls in the Cisco Unified Communications Manager Regions Configuration.

  3. Check that Video Capabilities are enabled under the Product Specific Configuration area for the device in Cisco Unified Communications Manager.

  4. Check the DSCP for Video Calls value in the Cisco Unified Communications Manager clusterwide parameters QoS configuration.

Answer: B

Question No: 74

Refer to the exhibits.

Ensurepass 2018 PDF and VCE

Assume that all learned SAF routes are placed in the SAF_Pt partition. An IP phone CSS contains the following partitions in this order: Internal_Pt, SAF_Pt. When the IP phone places a call to 3001, what will occur?

  1. The call will succeed and will be placed via the SAF network. SAF-learned routes always take precedence.

  2. The call will fail because it will be blocked by the route pattern.

  3. The call will be placed in a round-robin fashion between the SAF network and SIP_Trunk.

  4. The call will be placed in a round-robin fashion between the SAF network and SIP_Trunk. Every other call will fail.

Answer: B

Question No: 75

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

Local 10-digit dialing in the North American Numbering Plan to area code 456 is failing. Which two changes are needed to enable 10-digit dialing? (Choose two.)

  1. Change dial peer 210 to destination-pattern 456…….

  2. Change dial peer 210 to destination-pattern 9456…….

  3. Change dial peer 210 to port 0/0/0:23.

  4. Remove the command prefix 456 from dial peer 210.

Answer: B,C

Question No: 76

What is the meaning of this alarm snippet CCM_CALLMANAGER-CALLMANAGER-3- EndPointTfansientConnection?

  1. The device was successfully unregistered.

  2. The device was reset via the reset button in Cisco Unified Communications Manager.

  3. The device was misconfigured.

  4. The device was successfully registered.

Answer: C

Question No: 77

Which alarm string purges all learned patterns from the Cisco Unified Communications Manager?

  1. DuplicateLearnedPattern

  2. SAFForwarderError

  3. CCDIPReachableTimeOUT

  4. CCDPSTNFailOverDurationTimeOUT

  5. CCDLearnedPatternLimitReached

Answer: E

Question No: 78

Which three items are displayed on the endpoint registration verification page in Cisco VCS? (Choose three.)

  1. E.164 address

  2. endpoint name

  3. endpoint MAC address

  4. endpoint registration status

  5. device description

  6. device type

  7. device pool

Answer: A,B,F

Question No: 79

During a business-to-business video call through the Cisco Expressway solution, the internal endpoint can call out to the remote endpoint on the Internet, but it does not receive audio or video. The remote endpoint receives both audio and video. What is causing the issue?

  1. The Cisco Expressway does not have a Rich Media Session license.

  2. The firewall is blocking SIP signaling.

  3. The Cisco Unified Communications Manager is not configured for business-to-business calling.

  4. The firewall is blocking inbound RTP ports.

  5. The Advanced Networking option is not installed on the Expressway Edge.

Answer: D

Question No: 80

During a conference that is hosted on a Cisco TelePresence Server, which three circumstances determine that some participants do not have video, but they do have audio? (Choose three.)

  1. The participants have no video component.

  2. No free screen licensing ports are available.

  3. No video ports are available in a slave Cisco TelePresence Server configuration.

  4. The maximum number of participants is exceeded.

  5. In all Cisco TelePresence deployments, some participants are connected only via audio.

  6. No video ports are available in a single Cisco TelePresence Server configuration.

Answer: B,C,F

100% Ensurepass Free Download!
–Download Free Demo:300-080 Demo PDF
100% Ensurepass Free Guaranteed!
–300-080 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.