[Free] 2018(Jan) EnsurePass Testinsides Oracle 1z0-877 Dumps with VCE and PDF 101-110

By | January 25, 2018

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Oracle Official New Released 1z0-877
100% Free Download! 100% Pass Guaranteed!

Oracle Solaris 10 System Administrator Certified Professional Exam, Part IVersion 7.0

Question No: 101 – (Topic 2)

You are going to install a remote system using a WAN boot installation. Which two items are true of a WAN boot and must be part of your pre-installation checklist? (Choose two.)

  1. WAN boot is supported on machines with SPARC and x86 CPUs.

  2. You cannot use WAN boot on machines running the Solaris OS for x86 platforms.

  3. A CDROM is required to access the wanboot program and WAN boot miniroot.

  4. The system must have WAN boot support in the OBP or PXE support in the BIOS.

  5. An HTTP server must be available on the network.

Answer: B,E

Question No: 102 – (Topic 2)

You have completed the installation of the OS and you want to confirm what has been installed on the system. Where is the log file of the installation process stored?

  1. /var/adm/messages

  2. /var/install/contents

  3. /var/sadm/logs/install_data_logs

  4. /var/sadm/install_data/install_log

Answer: D

Question No: 103 – (Topic 2)

As system administrator, you have been asked to install a SPARC based system with the Solaris 10 OS. Which three are recommended system hardware requirements? (Choose three.)

  1. 128 megabytes of memory

  2. 256 megabytes of memory

  3. 5 gigabytes of disk space

  4. 3.2 gigabytes of disk space

  5. OpenBoot PROM firmware version 4.14 or later

  6. Access to a CD-ROM/DVD drive or an installation server

Answer: B,C,F

Question No: 104 – (Topic 2)

Which three FORTH Monitor commands allow you to boot a SPARC-based system? (Choose three.)

  1. ok boot net

  2. ok reboot

  3. ok boot net:rarp

  4. ok boot -as cdrom

E. ok boot ip=

Answer: A,C,D

Question No: 105 – (Topic 2)

You have added an additional internal drive to your x86-based desktop system, and you want to get the Solaris 10 OS to recognize it. Which two procedures will allow the OS to be able to recognize the new device? (Choose two).

  1. Boot the system then execute # touch /reconfigure, and then reboot the system. Confirm that you can see the new drive by executing # format.

  2. Boot the system and enter the # reconfigure command. Confirm that you can see the new drive by executing # format.

  3. Boot the system and enter the # devfsadm -v command. Confirm that you can see the new drive by executing # format.

  4. From the system menu, select the quot;Add new hardwarequot; icon. Confirm that you can see

Answer: A,C

Question No: 106 – (Topic 2)

Given: # svcadm milestone -d svc:/milestone/single-user:default Which two statements are true? (Choose two.)

  1. This system will boot to run level 3 at next boot.

  2. This system will boot to run level S at next boot.

  3. This system will have run level S as the default mode.

  4. The svcadm milestone -d svc:/milestone/multi-user:default should be run to return to run level 3.

  5. This system will not start svc.startd controlling services at the next boot.

Answer: B,C

Question No: 107 – (Topic 2)

There has been a PROM patch released and you need to check which revision your SPARC-based systems are currently using. Which two commands tell you the version? (Choose two.)

  1. prtconf -p

  2. prtconf -V

  3. cat /etc/release

  4. uname -a

  5. prtdiag -v

Answer: B,E

Question No: 108 – (Topic 2)

As system administrator, you are beginning the process of installing Solaris 10 OS on a new SPARC-based workstation. At the FORTH Monitor, which three will be displayed by initiating the banner command? (Choose three.)

  1. boot device

  2. input device

  3. Ethernet address

  4. OpenBoot version

  5. output device

  6. amount of memory

  7. diagnostics level

  8. diagnostics switch

Answer: C,D,F

Question No: 109 – (Topic 2)

Your Solaris x86-based server has two boot drives. You want to add an entry to the GRUB main menu, so that during the boot process, you can select to boot the server from either of the disk drives. How would you add a new entry to the GRUB main menu to allow the operator to select which drive to boot from?

  1. Edit the bootenv.rc file and enter a value for the altbootpath parameter.

  2. Use the kernel command to edit the boot entries in the GRUB main menu.

  3. Edit the menu.lst file and add an entry for the second boot disk to the GRUB main menu.

  4. When the GRUB menu appears during the boot process, type edit the GRUB menu and enter the command to boot from the alternate disk drive.

  5. Press the space bar when the GRUB menu is visible during the boot process to edit the list of commands and enter the command to boot to the alternate disk drive.

Answer: C

Question No: 110 – (Topic 2)

A new service named banner has been written that needs to be incorporated into SMF. The appropriate entries have been placed in the milestones where this service is stopped and started and the service scripts are in the correct locations. Which command will incorporate the banner service into SMF?

  1. svcadm add /var/svc/manifest/site/banner-smf-xml

  2. svccfg add /var/svc/manifest/site/banner-smf.xml

  3. svccfg import /var/svc/manifest/site/banner-smf.xml

  4. svcadm import /var/svc/manifest/site/banner-smf.xml

Answer: C

100% Ensurepass Free Download!
Download Free Demo:1z0-877 Demo PDF
100% Ensurepass Free Guaranteed!
1z0-877 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.