[Free] 2018(June) Dumps4cert CompTIA RC0-903 Dumps with VCE and PDF Download 41-50

By | July 8, 2018

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 May CompTIA Official New Released RC0-903
100% Free Download! 100% Pass Guaranteed!

CompTIA A Recertification Exam for Continuing Education

Question No: 41 – (Topic 2)

Joe, a user, receives a wireless router from his ISP with a pre-set password and configuration. He can connect to the router fine via Ethernet but cannot see the wireless signal on any of his devices. The LEDs on the router indicate that a wireless signal is broadcasting. Which of the following settings on the router does Joe need to adjust to enable the devices to see the wireless signal?

  1. DHCP

  2. IPv6

  3. DMZ

  4. SSID

Answer: D

Question No: 42 – (Topic 2)

A workstation has a network link light, but it cannot access internal network resources. Which of the following is the MOST likely cause of the issue?

  1. Slow transfer speeds

  2. IP address conflict

  3. Incorrect gateway

  4. Packet collisions

Answer: B

Question No: 43 – (Topic 2)

A user reports an inkjet printer is constantly feeding two sheets of paper for every page printed. Which of the following is the MOST likely reason?

  1. Poor paper quality

  2. Incorrect paper size

  3. Defective duplexer

  4. Worn feed rollers

Answer: D

Question No: 44 – (Topic 2)

A technician is tasked with upgrading the hard drives of a high-end workstation to SSD. The drives must be configured in a RAID array, but the RAID card does not support SSD. Which of the following would the technician verify in order to use the new drives?

  1. Controller firmware

  2. Power requirements

  3. File system type

  4. System BIOS

Answer: A

Question No: 45 – (Topic 2)

A user reports that the mouse is not working properly. The technician notices on the user’s workstation that the mouse cursor spins for several minutes before the technician can use the mouse. Which of the following is the cause of the issue?

  1. Failed Operating System

  2. Faulty mouse

  3. Faulty CPU

  4. Not enough memory

Answer: D

Question No: 46 – (Topic 2)

After receiving a call from an executive, a technician walks into a meeting room to find that the projector is not showing the screen of the executive’s laptop. The projector shows a message that reads “No video signal”. Which of the following is the FIRST thing that the technician should do?

  1. Adjust the laptop#39;s screen brightness

  2. Replace the projector#39;s bulb

  3. Verify the VGA cable is connected

  4. Ensure secondary display is enabled

Answer: C

Question No: 47 – (Topic 2)

A client, Ann, is having issues with a PC shutting down. There are no error messages displayed before the system powers off. Ann reports that this started after she installed and began using CAD software. The hard drive, video card, and RAM all meet the software

requirements and have passed diagnostics. Which of the following is MOST likely the issue?

  1. The video card has 3D acceleration disabled.

  2. The hard drive is IDE instead of SATA.

  3. The hard drive needs to be repartitioned.

  4. The PSU is underpowered for the system.

Answer: D

Question No: 48 – (Topic 2)

A client’s computer is not connecting to a website. Which of the following commands will allow the technician to view the route/number of hops between the host and remote systems?

  1. nbtstat

  2. tracert

  3. nslookup

  4. netstat

Answer: B

Question No: 49 – (Topic 2)

A technician has upgraded the BIOS of a system that is running with multiple hard drives. Afterward, the system will not boot and displays an error message “Operating system not found”. Which of the following is the FIRST thing the technician should inspect?

  1. The hard drive type settings in the BIOS

  2. The power supply connections to the hard drives

  3. The boot sequence settings in the BIOS

  4. The motherboard SATA connectors

Answer: C

Question No: 50 – (Topic 2)

Joe, a technician, is preparing to replace a laptop screen. This laptop has a touch screen to support Windows 8.1 in order to use the Metro tiles. Which of the following is the FIRST step the technician should perform?

  1. Remove the laptop bezel

  2. Document and label each cable and screw location

  3. Organize the replacement parts

  4. Refer to the manufacturer’s documentation

Answer: D

100% Dumps4cert Free Download!
Download Free Demo:RC0-903 Demo PDF
100% Dumps4cert Pass Guaranteed!
RC0-903 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.