[Free] 2018(June) Dumps4cert CompTIA RC0-N06 Dumps with VCE and PDF Download 171-180

By | July 10, 2018

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 May CompTIA Official New Released RC0-N06
100% Free Download! 100% Pass Guaranteed!

CompTIA Network Recertification Exam for Continuing Education

Question No: 171 – (Topic 6)

Ann, a system administrator, is troubleshooting an issue with a DNS server. She notices that the security logs have filled up and that they need to be cleared from the event viewer. She recalls this being a daily occurrence. Which of the following solutions would BEST resolve this problem?

  1. Increase the maximum log size

  2. Log into the DNS server every hour to check if the logs are full

  3. Install an event management tool

  4. Delete the logs when full

Answer: C

Question No: 172 – (Topic 6)

Which of the following ports does SIP use?

A. 443

B. 1720

C. 2427/27/27 D. 5004/5005 E. 5060/5061

Answer: E Explanation:


Question No: 173 – (Topic 6)

There has been an increased amount of successful social engineering attacks at a corporate office. Which of the following will reduce this attack in the near future?

  1. Helpdesk training

  2. Appropriate use policy

  3. User awareness training

  4. Personal Identifiable Information

Answer: C

Question No: 174 – (Topic 6)

A network technician has been tasked to provide a local office with wireless Internet access. The network technician had determined the users will need a wireless router that provides a maximum of 54Mbps of bandwidth while operating in the 2.4Ghz band. Which of the following wireless standards will the network technician deploy?

A. 802.11a B. 802.11b C. 802.11g D. 802.11n

Answer: C Explanation:

802.11g provides transmission over short distances at up to 54Mbps in the 2.4GHz bands.

Question No: 175 – (Topic 6)

A network technician is troubleshooting connectivity problems between switches but suspects the ports are not properly labeled. Which of the following options will help to quickly identify the switches connected to each port?

  1. Configure TACACs on each network device.

  2. Enable a discovery protocol on the network devices.

  3. Configure each uplink to send LACP discovery units.

  4. Enable a packet sniffer on each network device’s uplink port.

Answer: B Explanation:

“Neighbor discovery protocols are essential for network administrators and management tools to accurately construct a view of the network topology. Each manufacturer has its own supported mix of neighbor discovery protocols, loosely based on how standards-focused that vendor is and how much it wants to pay in royalties to use proprietary protocols. The two most widely used are LLDP (Link Layer Discovery Protocol), an IEEE standard, and CDP (Cisco Discovery Protocol).”


http://www.networkcomputing.com/networking/5-basic-switch-settings-you-must- know/879127198

Question No: 176 – (Topic 6)

A network technician is connecting three temporary office trailers with a point-to-multipoint microwave radio solution in a wooded area. The microwave radios are up and the network technician can ping devices in all office trailers, however, connectivity is sporadic. Which of the following is MOST likely the cause of this issue?

  1. Latency

  2. Throttling

  3. Interference

  4. Split horizon

Answer: C

Question No: 177 – (Topic 6)

A technician is looking at an issue with a computer connecting to the network. The technician determines wire 3 of a UTP Ethernet cable run has a break in it. This computer was previously connected to the switch at 1Gbps throughput. This PC is a kiosk and does not need anything more than 50-60Mbps connection speed. Which of the following can the technician do to resolve the issue quickly?

  1. Rewire both ends to have the wire on pin 6 remapped to pin 3. Force the duplex and speed to 100Mbps full duplex.

  2. Rewire both ends to have the wire on pin 6 remapped to pin 3. Force the duplex and speed to 1000Mbps full duplex.

  3. Rewire both ends to have the wire on pin 7 remapped to pin 3. Force the duplex and speed to 100Mbps full duplex.

  4. Rewire both ends to have the wire on pin 7 remapped to pin 3. Force the duplex and speed to 1000Mbps full duplex.

Answer: D Explanation:


Question No: 178 – (Topic 6)

Which of the following describes a design where traffic is shared between multiple network servers to provide greater throughput and reliability?

  1. Load balancing

  2. MPLS trunking

  3. VLAN tagging

  4. Multiplexing

Answer: A

Question No: 179 – (Topic 6)

A contractor was hired to troubleshoot congestion issues on the network. After a few of the switches have been reconfigured/upgraded by the contractor, congestion worsens and collisions increase. Which of the following is the BEST action to alleviate the situation?

  1. Allow the contractor to reset switches to factory defaults

  2. Check the cabling on all switches for improper crossover use

  3. Document the changes thatwere made

  4. Downgrade firmware and restore backup configuration

Answer: D

Question No: 180 – (Topic 6)

A company that was previously running on a wired network is performing office-wide upgrades. A department with older desktop PC#39;s that do not have wireless capabilities

must be migrated to the new network, ensuring that all computers are operating on a single network. Assuming CAT5e cables are available, which of the following network devices should a network technician use to connect all the devices to the wireless network?

  1. Wireless bridge

  2. VPN concentrator

  3. Default WAP

  4. Wireless router

Answer: D

100% Dumps4cert Free Download!
Download Free Demo:RC0-N06 Demo PDF
100% Dumps4cert Pass Guaranteed!
RC0-N06 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.