QUESTION 111
Refer to the exhibit. How many EIGRP routes will appear in the routing table of R2?
|
A. |
0 |
|
B. |
1 |
|
C. |
2 |
|
D. |
3 |
Correct Answer: A
Explanation:
EIGRPv6 on R2 was shut down so there is no EIGRP routes on the routing table of R2. If we turn on EIGRPv6 on R2 (with “no shutdown” command) then we would see the prefix of the loopback interface of R1 in the routing table of R2.
Note: EIGRPv6 requires the “ipv6 unicast-routing” global command to be turned on first or it will not work.
QUESTION 112
Refer to the exhibit. Which VLANs are permitted to send frames out port FastEthernet0/1?
|
A. |
100 – 200 |
|
B. |
4 – 100 |
|
C. |
1 and 4 – 100 |
|
D. |
3 and 4 – 100 |
Correct Answer: D
Explanation:
Traffic on the native vlan does not get tagged as it crosses a trunk, so there is no dot1q tag in the first place to be filtered. And you don’t need to allow the native vlan. But if we force to tag the native vlan (with the “switchport trunk native vlan tag” command) then if the native vlan is not in the “allowed vlan” list it will be dropped.
QUESTION 113
Which two statements are true about IPv6 multicast? (Choose two.)
|
A. |
Receivers interested in IPv6 multicast traffic use IGMPv6 to signal their interest in the IPv6 multicast group. |
|
B. |
The PIM router with the lowest IPv6 address becomes the DR for the LAN. |
|
C. |
An IPv6 multicast address is an IPv6 address that has a prefix of FF00::/8. |
|
D. |
The IPv6 all-routers multicast group is FF02:0:0:0:0:0:0:2. |
Correct Answer: CD
Explanation:
Multicast addresses in IPv6 have the prefix ff00::/8.
Well-known IPv6 multicast addresses
Address
Description
ff02::1
All nodes on the local network segment
ff02::2
All routers on the local network segment
Reference: http://en.wikipedia.org/wiki/Multicast_address
QUESTION 114
Which two options are advantages of NetFlow version 9 over NetFlow version 5? (Choose two.)
|
A. |
NetFlow version 9 adds support for IPv6 headers. |
|
B. |
NetFlow version 9 adds support for MPLS labels. |
|
C. |
NetFlow version 9 adds support for the Type of Service field. |
|
D. |
NetFlow version 9 adds support for ICMP types and codes. |
Correct Answer: AB
Explanation:
NetFlow version 9 includes support for all of these fields that version 5 supports and can optionally include additional information such as Multiprotocol Label Switching (MPLS) labels and IPv6 addresses and ports.
QUESTION 115
Refer to the exhibit. Which two statements are true? (Choose two.)
|
A. |
This is the output of the show ip ospf command. |
|
B. |
This is the output of the show ip protocols command. |
|
C. |
This router is an ABR. |
|
D. |
This router is an ASBR. |
|
E. |
Authentication is not configured for the area. |
Correct Answer: AE
Explanation:
The following is sample output from the show ip ospf command when entered without a specific OSPF process ID with no authentication
Router# show ip ospf
Routing Process “ospf 201” with ID 10.0.0.1 and Domain ID 10.20.0.1
Supports only single TOS(TOS0) routes
Supports opaque LSA
SPF schedule delay 5 secs, Hold time between two SPFs 10 secs
Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs
LSA group pacing timer 100 secs
Interface flood pacing timer 55 msecs
Retransmission pacing timer 100 msecs
Number of external LSA 0. Checksum Sum 0x0
Number of opaque AS LSA 0. Checksum Sum 0x0
Number of DCbitless external and opaque AS LSA 0
Number of DoNotAge external and opaque AS LSA 0
Number of areas in this router is 2. 2 normal 0 stub 0 nssa
External flood list length 0
Area BACKBONE(0)
Number of interfaces in this area is 2
Area has no authentication
SPF algorithm executed 4 times
Area ranges are
Number of LSA 4. Checksum Sum 0x29BEB
Number of opaque link LSA 0. Checksum Sum 0x0
Number of DCbitless LSA 3
Number of indication LSA 0
Number of DoNotAge LSA 0
Flood list length 0
Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/command/iro-cr-book/ospf-s1.html#wp8749965360
QUESTION 116
Refer to the exhibit. Which two statements about the output are true? (Choose two.)
|
A. |
802.1D spanning tree is being used. |
|
B. |
Setting the priority of this switch to 0 for VLAN 1 would cause it to become the new root. |
|
C. |
The hello, max-age, and forward delay timers are not set to their default values. |
|
D. |
Spanning-tree PortFast is enabled on GigabitEthernet1/1. |
Correct Answer: AB
Explanation:
802.1D is the standard for Spanning tree, which is being used here. For priority, The priority order starts from 0 (yes, 0 is valid) and then increases in 4096.
0, 4096, 8192, 12288, …. Etc.
The lower the number, the higher the priority. Here we see that the current root has a priority of 8192, so configuring this with a priority of 0 will make it the new root.
QUESTION 117
Refer to the exhibit. What is the PHB class on this flow?
|
A. |
EF |
|
B. |
none |
|
C. |
AF21 |
|
D. |
CS4 |
Correct Answer: D
Explanation:
This command shows the TOS value in hex, which is 80 in this case. The following chart shows some common DSCP/PHB Class values:
Service
DSCP value
TOS value
Juniper Alias
TOS hexadecimal
DSCP – TOS Binary
Premium IP
46
184
ef
B8
101110 – 101110xx
LBE
8
32
cs1
20
001000 – 001000xx
DWS
32
128
cs4
80
100000 – 100000xx
Network control
48
192
cs6
c0
110000 – 110000xx
Network control 2
56
224
cs7
e0
111000 – 111000xx
Reference: http://www.tucny.com/Home/dscp-tos
QUESTION 118
Refer to the exhibit. Which two statements are true about the displayed STP state? (Choose two.)
|
A. |
The STP version configured on the switch is IEEE 802.1w. |
|
B.< /font> |
Port-channel 1 is flapping and the last flap occurred 1 minute and 17 seconds ago. |
|
C. |
The switch does not have PortFast configured on Gi0/15. |
|
D. |
BPDUs with the TCN bit set are transmitted over port channel 1. |
Correct Answer: CD
Explanation:
A port enabled with portfast will not send topology changes when a port goes up or down, but here we see that 296 TCN’s were sent so we know that Gi 0/15 does not have portfast enabled. TCN’s are sent using BPDU’s over the root port, which we see is port channel 1.
QUESTION 119
Which Carrier Ethernet service supports the multiplexing of multiple point-to-point EVCs across as a single UNI?
|
A. |
EPL |
|
B. |
EVPL |
|
C. |
EMS |
|
D. |
ERMS |
Correct Answer: B
Explanation:
Ethernet Relay Service (ERS or EVPL)
An Ethernet Virtual Circuit (EVC) is used to logically connect endpoints, but multiple EVCs could exist per single UNI. Each EVC is distinguished by 802.1q VLAN tag identification. The ERS network acts as if the Ethernet frames have crossed a switched network, and certain control traffic is not carried between ends of the EVC. ERS is analogous to Frame Relay where the CE-VLAN tag plays the role of a Data-Link Connection Identifier (DLCI). The MEF term for this service is EVPL.
Reference: http://www.cisco.com/c/en/us/td/docs/net_mgmt/ip_solution_center/5-1/carrier_ethernet/user/guide/l2vpn51book/concepts.html
QUESTION 120
Refer to the exhibit. Video Source S is sending interactive video traffic to Video Receiver R. Router R1 has multiple routing table entries for destination R. Which load-balancing mechanism on R1 can cause out-of-order video traffic to be received by destination R?
|
A. |
per-flow load balancing on R1 for destination R |
|
B. |
per-source-destination pair load balancing on R1 for destination R |
|
C. |
CEF load balancing on R1 for destination R |
|
D. |
per-packet load balancing on R1 for destination R |
Correct Answer: D
Explanation:
Per-packet load balancing guarantees equal load across all links, however potentially the packets may arrive out-of-order at the destination as differential delay may exist within the network.
Reference: http://www.cisco.com/en/US/products/hw/modules/ps2033/prod_technical_reference09186a00800 afeb7.html
Free VCE & PDF File for Cisco 400-101 Real Exam
Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …