Free Download New Updated Cisco CCIE R&S 400-101 Real Exam Questions and Answers 291-300

By | October 20, 2014

Ensurepass

QUESTION 291

Refer to the exhibit. Router RTB is performing one-way redistribution from RIP to OSPF. Which outgoing interface will router RTD choose for packets to the 192.168.0.0/24 network, and why?

 

clip_image001

 

A.

Fa0/1, because OSPF is a link-state routing protocol

B.

Fa0/0, because RIP is a distance vector protocol

C.

Fa0/0, because RIP has a higher administrative distance

D.

Fa0/0, because OSPF has a lower administrative distance

E.

Fa0/1, because OSPF has a lower administrative distance

F.

Fa0/1, because RIP has a lower administrative distance

 

Correct Answer: D

 

 

QUESTION 292

Refer to the exhibit. You have performed multiple changes to your OSPF configuration. After these changes, you receive a lot of calls from users in OSPF area 2 complaining about application performance issues when they access servers connected to area 3. When you check the routing table of router RTC, you notice that packets to network 10.3.3.0/24 are sent out via the slower path out of the Fa0/0 interface. What can you do to solve this issue?

 

clip_image003

 

A.

Change the OSPF configuration in OSPF area 1 to OSPF area 0

B.

Change the OSPF configuration in OSPF area 0 to OSPF area 1

C.

Change the OSPF configuration in OSPF area 2 to OSPF area 3

D.

Change the OSPF configuration in OSPF area 3 to OSPF area 1

 

Correct Answer: A

 

QUESTION 293

Refer to the exhibit. You get reports that Windows users cannot log in anymore when the main MPLS link is down. The message that users receive is, “There are currently no login servers available to service the login request.” However, if you modify the MTU of the client machine to 1294, the user can log in. What would be a reliable fix for this issue?

 

clip_image004

 

A.

add “ip tcp mss-adjust 1254” to se1/0/0

B.

add “ip tcp mss-adjust 1254” to se1/0/0 and fa1/0

C.

force Windows to use TCP for Kerberos

D.

add “ip icmp error-send” to se1/0/0

 

Correct Answer: C

 

 

QUESTION 294

Refer to the exhibit. What problem does the debug ip ospf event output from R4 indicate?

 

clip_image006

 

A.

a mismatched dead timer between R4 and 209.165.202.130

B.

a mismatched hello timer between R4 and 209.165.202.130

C.

mismatched areas between R4 and 209.165.202.130

D.

mismatched masks between R4 and 209.165.202.130

 

Correct Answer: D

 

 

QUESTION 295

Refer to the exhibit. What is preventing R4 from learning any networks via OSPF?

 

clip_image008

 

A.

R4 does not have any OSPF neighbors.

B.

There is no OSPF backup designated router on FastEthernet0/0.

C.

The OSPF area number for FastEthernet0/0 does not match the interface network.

D.

There are no OSPF learned routes in the network beyond R4.

 

Correct Answer: A

 

 

QUESTION 296

Refer to the exhibit. Which result will the EEM applet in the exhibit produce?

 

clip_image009

 

A.

The output of show version will be executed every 5 hours.

B.

The output of show log will be executed every 5 hours.

C.

The output of show log will be executed every Friday.

D.

The output of show log will be executed every 5 minutes.

 

Correct Answer: B

 

 

 

 

 

 

QUESTION 297

Refer to the exhibit. Based on the above commands, when will the output of the show log command be saved?

 

clip_image011

 

A.

Each time the total CPU utilization goes below 50 percent

B.

Each time the total CPU utilization goes above 80 percent

C.

Every 5 minutes while the total CPU utilization is above 80 percent

D.

Every 5 seconds while the total CPU utilization is above 80 percent

E.

Every 5 minutes while the total CPU utilization is below 50 percent

F.

Every 5 seconds while the total CPU utilization is below 50 percent

 

Correct Answer: D

 

 

QUESTION 298

Choose two commands that are required to enable multicast on a router, when it is known that the receivers use a specific functionality of IGMPv3. (Choose two.)

 

A.

ip pim rp-address

B.

ip pim ssm

C.

ip pim sparse-mode

D.

ip pim passive

 

Correct Answer: BC

 

 

QUESTION 299

Refer to the exhibit. R1 has two eBGP sessions to ISP1 and ISP2 (one to each ISP router), and R1 receives the same prefixes through both links. Which configuration should be applied for the link between R1 and ISP2 to be preferred for incoming traffic (ISP2 to R1)?

 

clip_image012

 

A.

increase local preference on R1 for sent routes

B.

decrease local preference on R1 for sent routes

C.

increase MED on ISP2 for sent routes

D.

decrease MED on ISP2 for sent routes

 

Correct Answer: D

 

 

QUESTION 300

Refer to the exhibit. A new Ethernet link was added to an existing OSPF network. It is possible to ping the remote end of the link, but the OSPF adjacency does not form. Which two commands configured on the interface could resolve the issue? (Choose two.)

 

clip_image014

 

A.

ip ospf mtu-ignore

B.

ip ospf flood-reduction

C.

ip mtu 1500

D.

ip mss 1500

 

Correct Answer: AC

 

Instant Access to Download Latest Complete Collection of Cisco CCIE R&S 400-101 Real Exam

Try Cisco CCIE R&S 400-101 Free Demo