[Free] Download New Updated (February 2016) Cisco 210-065 Practice Tests 51-60

By | February 12, 2016

Ensurepass

QUESTION 51

Which MCU supports the use of a lobby screen?

 

A.

CTMS

B.

TS 8710

C.

MCU 5300

D.

Conductor

 

Correct Answer: B

 

 

QUESTION 52

Which Cisco TelePresence Multipoint Control Unit Layout view mode gives prominence to one conference participant over the other conference participants while still allowing conference participants to view
multiple participants at the same time?

 

A.

enhanced continuous presence

B.

active speaker

C.

continuous presence

D.

room switching

E.

speaker switching

 

Correct Answer: A

 

 

QUESTION
53

Which two of these can cause registration problems for a Cisco TelePresence Codec C40 endpoint running in H.323 mode? (Choose two.)

 

A.

The IP default gateway address is incorrect for the endpoint.

B.

The H.323 license stack is not added to the endpoint.

C.

The MAC address for the endpoint has not been added to the Cisco TelePresence VCS.

D.

The E.164 H323Alias has not been configured on the endpoint.

E.

The URI address has not been configured on the endpoint.

 

Correct Answer: AD

 

 

QUESTION 54

An engineer needs to configure cascading to support additional video conference attendees. What are three capabilities when cascading? (Choose three.)

 

A.

Conductor automatically performs cascading.

B.

A maximum of four multipoint control units are supported.

C.

Cascading is supported for the Cisco TelePresence Server in remotely managed mode.

D.

It is possible to manually create a cascaded conference via the Cisco TelePresence MCU Management API.

E.

Cascading is supported for multipoint control units that are registered to Cisco Unified Communications Manager.

F.

All cascaded multipoint control units must be in the same location.

 

Correct Answer: ACD

 

 

QUESTION 55

Refer to the exhibit. For Cisco TelePresence endpoints with TC7.0 software, configuration backup and restore appears where?

 

clip_image002

 

A.

Call Control tab

B.

Configuration tab

C.

Diagnostics tab

D.

Maintenance tab

E.

Home tab

 

Correct Answer: D

 

 

QUESTION 56

Cisco Video Surveillance Video Encoder cards perform which function?

 

A.

the ability to use existing analog equipment with an IP-enabled video surveillance system

B.

the ability to convert low-resolution video to high-definition video for video surveillance

C.

the ability to stream digital media to digital media in an IP-enabled video recording environment

D.

the ability to encrypt raw video signals to secure video signals

 

Correct Answer: A

 

 

QUESTION 57

A network engineer is setting up a Cisco TelePresence Content Server. The customer requires live streaming, but does not have a streaming server. Which media should be configured to stream locally from the TelePresence Content Server?

 

A.

QuickTime

B.

MPEG-4

C.

Flash

D.

Windows Media

E.

Darwin

 

Correct Answer: D

 

 

 

 

QUESTION 58

A network administrator is troubleshooting a video issue from the Cisco VCS CLI and wants to see the ongoing calls. Which command should the administrator use?

 

A.

xconfiguration calls

B.

xcommand calls

C.

xcalls status

D.

xstatus calls

 

Correct Answer: D

 

 

QUESTION 59

Refer to the exhibit. What can be deduced from the log shown in the exhibit, which was taken from a Cisco TelePresence Codec C60?

 

clip_image004

 

A.

A direct call to 52902511 is being made.

B.


A Multiway call to multiway221@osl147.local is being made.

C.

No calls are being attempted by the endpoint.

D.

A BFCP call is being initiated.

E.

The endpoint is receiving a call from the VCS.

 

Correct Answer: B

 

 

QUESTION 60

An engineer needs to connect an external display to a Cisco TelePresence MX700 endpoint. What must the engineer do to access the external monitor output connector?

 

A.

Remove the cover under the main monitor. The cover is fastened with two screws.

B.

Remove the cover on the back of the system. The cover is fastened with magnets.

C.

Remove the cover on the right side of the system. The cover is fastened with four screws.

D.

Remove the cover on the left side of the system. The cover is fastened with magnets.

 

Correct Answer: D

 

Free VCE & PDF File for Cisco 210-065 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …