Latest Cisco 200-101 ICND2 Real Exam Download 191-200

By | August 16, 2013



What is the default administrative distance of OSPF?


A.        90

B.        100

C.        110

D.        120


Correct Answer: C




Refer to the exhibit. What can be determined about the interfaces of the Main_Campus router from the output shown?




A.       The LAN interfaces are configured on different subnets.

B.        Interface FastEthernet 0/0 is configured as a trunk

C.        The Layer 2 protocol of interface Serial 0/1 is NOT operational.

D.       The router is a modular router with five FastEthernet interfaces.

E.        Interface FastEthernet 0/0 is administratively deactivated.


Correct Answer: B




Refer to the exhibit. How should Switch1 and Switch2 be connected in order to allow full communication between all of the hosts?

























Correct Answer: F




Refer to the exhibit. At the end of an RSTP election process, which access layer switch port will assume the discarding role?




A.       Switch3, port fa0/1

B.        Switch3, port fa0/12

C.        Switch4, port fa0/11

D.       Switch4, port fa0/2

E.        Switch3, port Gi0/1

F.        Switch3, port Gi0/2


Correct Answer: C






Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely reason that interface FastEthernet 0/10 is not the root port for VLAN 2?




A.       This switch has more than one interface connected to the root network segment in VLAN 2.

B.        This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.

C.        This switch interface has a higher path cost to the root bridge than another in the topology.

D.       This switch has a lower bridge ID for VLAN 2 than the elected designated switch.


Correct Answer: C




Select the action that results from executing these commands.


Switch(config-if)# switchport port-security

Switch(config-if)# switchport port-security mac-address sticky


A.       A dynamically learned MAC address is saved in the startup-configuration file.

B.        A dynamically learned MAC address is saved in the running-configuration file.

C.        A dynamically learned MAC address is saved in the VLAN database.

D.       Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.

E.        Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.


Correct Answer: B





Refer to the exhibit. Some 2950 series switches are connected to the conference area of the corporate headquarters network. The switches provide two to three jacks per conference room to host laptop connections for employees who visit the headquarters office. When large groups of employees come from other locations, the network administrator often finds that hubs have been connected to wall jacks in the conference area although the ports on the access layer switches were not intended to support multiple workstations. What action could the network administrator take to prevent access by multiple laptops through a single switch port and still leave the switch functional for its intended use?




A.       Configure static entries in the switch MAC address table to include the range of addresses used by visiting employees.

B.        Configure an ACL to allow only a single MAC address to connect to the switch at one time.

C.        Use the mac-address-table 1 global configuration command to limit each port to one source MAC address.

D.       Implement Port Security on all interfaces and use the port-security maximum 1 command to limit port access to a single MAC address.

E.        Implement Port Security on all interfaces and use the port-security mac-address sticky command to limit access to a single MAC address.

F.        Implement Port Security at global configuration mode and use the port-security maximum 1 command to allow each switch only one attached hub.


Correct Answer: D




Refer to the exhibit. Which two statements about the configuration of the switch interface are correct? (Choose two.)




A.       The switchport belongs only to VLAN 2.

B.        By default, all switch ports are members of VLAN 1005.

C.        Interface fa0/0 will be in both VLAN 1 (by default) and VLAN 2.

D.       The exhibit shows interface fa0/0 to be dynamically mapped to VLAN 2.

E.        A network host can be connected to this interface.


Correct Answer: AE




Refer to the exhibit. Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.)




A.       SwitchA, Fa0/2, designated

B.        SwitchA, Fa0/1, root

C.        SwitchB, Gi0/2, root

D.       SwitchB, Gi0/1, designated

E.        SwitchC, Fa0/2, root

F.        SwitchD, Gi0/2, root


Correct Answer: ABF




Which three elements must be used when you configure a router interface for VLAN trunking? (Choose three.)


A.       one physical interface for each subinterface

B.        one IP network or subnetwork for each subinterface

C.        a management domain for each subinterface

D.       subinterface encapsulation identifiers that match VLAN tags

E.        one subinterface per VLAN

F.        subinterface numbering that matches VLAN tags


Correct Answer: BDE




Download Latest Cisco 200-101 ICND2 Real Free Tests , help you to pass exam 100%.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.