Latest Cisco 200-101 ICND2 Real Exam Download 211-220

By | August 16, 2013



Refer to the exhibit. A technician pastes the configurations in the exhibit into the two new routers shown. Otherwise, the routers are configured with their default configurations. A ping from Host1 to Host2 fails, but the technician is able to ping the S0/0 interface of R2 from Host1. The configurations of the hosts have been verified as correct. What could be the cause of the problem?




A.       The serial cable on R1 needs to be replaced.

B.        The interfaces on R2 are not configured properly.

C.        R1 has no route to the network.

D.       The IP addressing scheme has overlapping subnetworks.

E.        The ip subnet-zero command must be configured on both routers.


Correct Answer: C




A router is running three routing processes: RIP, OSPF, and EIGRP, each configured with default characteristics. Each process learns a route to the same remote network. If there are no static routes to the destination and none of the routes were redistributed, which route will be placed in the IP routing table?


A.       the route learned through EIGRP

B.        the route learned through OSPF

C.        the route learned through RIP

D.       the route with the lowest metric

E.        all three routes with the router load balancing

Correct Answer: A




A network administrator needs to allow only one Telnet connection to a router. For anyone viewing the configuration and issuing the show run command, the password for Telnet access should be encrypted. Which set of commands will accomplish this task?


A.       service password-encryption

access-listl permit

line vty0 4


password cisco

access-class 1


B.        enable password secret

line vty0


password cisco


C.        service password-encryption

line vty0


password cisco


D.       service password-encryption

line vty0 4


password cisco


Correct Answer: C






Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?









Correct Answer: C




Which command can be used from a router to verify the Layer 3 path to a host?


A.       tracert address

B.        traceroute address

C.        telnet address

D.       ssh address


Correct Answer: B




An access list has been designed to prevent Telnet traffic from the Graphics Department from reaching the HR server attached to the Eastfield router but allow Telnet traffic to other destinations. Given the following access list:


access-list 101 deny tcp any any eq 23

permit ip any any


On which router, interface, and in what direction should the access list be placed to most efficiently implement this list? (Choose three.)


A.      Westfield

B.      Eastfield

C.      e0

D.      s0

E.       in

F.       out


Correct Answer: BCF




Which form of NAT maps multiple private IP addresses to a single registered IP address by using different ports?


A.       static NAT

B.        dynamic NAT

C.        overloading

D.       overlapping

E.        port loading


Correct Answer: C




Unauthorized users have used Telnet to gain access to a company router. The network administrator wants to configure and apply an access list to allow Telnet access to the router, but only from the network administrator’s computer. Which group of commands would be the best choice to allow only the IP address to have Telnet access to the router?


A.       access-list 101 permit tcp any host eq telnet

interface s0/0

ip access-group 101 in


B.        access-list 3 permit host

line vty 0 4

access-class 3 in


C.        access-list 101 permit tcp any host eq telnet

access-list 101 permit ip any any

interface s0/0

ip access-group 101 in


D.       access-list 3 permit host

line vty 0 4

ip access-group 3 in


Correct Answer: B




Refer to the exhibit. What command sequence will enable PAT from the inside to outside network?




A.       (config) ip nat pool isp-net netmask overload

B.        (config-if) ip nat outside overload

C.        (config) ip nat inside source list 1 interface ethernet1 overload

D.       (config-if) ip nat inside overload


Correct Answer: C




Which two statements about static NAT translations are true? (Choose two.)


A.       They allow connections to be initiated from the outside.

B.        They require no inside or outside interface markings because addresses are statically defined.

C.        They are always present in the NAT table.

D.       They can be configured with access lists, to allow two or more connections to be initiated from the outside.


Correct Answer: AC



Download Latest Cisco 200-101 ICND2 Real Free Tests , help you to pass exam 100%.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.