Latest Cisco 200-101 ICND2 Real Exam Download 241-250

By | August 16, 2013

Ensurepass

QUESTION 241

Refer to the exhibit. The network is converged. After link-state advertisements are received from Router_A, what information will Router_E contain in its routing table for the subnets 208.149.23.64 and 208.149.23.96?

 

clip_image002

 

A.      208.149.23.64[110/13] via 190.173.23.10,00:00:07, FastEthemet0/0

208.149.23.96[110/13] via 190.173.23.10,00:00:16, FastEthemet0/0

 

B.      208.149.23.64[110/1] via 190.172.23.10,00:00:07, Serial1/0

208.149.23.96[110/3] via 190.173.23.10,00:00:16, FastEthemet0/0

 

C.      208.149.23.64[110/13] via 190.173.23.10,00:00:07, Serial1/0

208.149.23.96[110/13] via 190.173.23.10,00:00:16, Serial1/0

208.149.23.96[110/13] via 190.173.23.10,00:00:16, FastEthemet0/0

 

D.      208.149.23.96[110/3] via 190.173.23.10,00:00:16, Serial1/0

208.149.23.96[110/3] via 190.173.23.10,00:00:16, Serial1/0

 

Correct Answer: A

 

 

QUESTION 242

Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?

 

clip_image003

 

A.       AS numbers must be changed to match on all the routers

B.        Loopback interfaces must be configured so a DR is elected

C.        The no auto-summary command is needed on Router A and Router C

D.       Router B needs to have two network statements, one for each connected network

 

Correct Answer: A

 

 

QUESTION 243

Which command reveals the last method used to powercycle a router?

 

A.       show reload

B.        show boot

C.        show running-config

D.       show version

 

Correct Answer: D

 

 

QUESTION 244

Which two statements are characteristics of a distance vector routing protocol? (Choose two.)

 

A.       Each router has its own view of the topology.

B.        Updates are periodic and include the entire routing table.

C.        Routing updates are sent only after topology changes.

D.       Convergence is usually faster than with link state protocols.

E.        RIP is an example of distance vector routing protocols.

F.        The protocol can be useful in hub-and-spoke and hierarchical networks.

 

Correct Answer: BE



 


QUESTION 245

Which two Cisco IOS commands, used in troubleshooting, can enable debug output to a remote location? (Choose two.)

 

A.       terminal monitor

B.        logging host ip-address

C.        no logging console

D.       snmp-server enable traps syslog

E.        show logging | redirect flash:output.txt

 

Correct Answer: AB

 

 

QUESTION 246

Which parameter can be tuned to affect the selection of a static route as a backup, when a dynamic protocol is also being used?

 

A.       hop count

B.        administrative distance

C.        link bandwidth

D.       link delay

E.        link cost

 

Correct Answer: B

 

 

QUESTION 247

Which command is necessary to permit SSH or Telnet access to a Cisco switch that is otherwise configured for these vty line protocols?

 

A.       transport output all

B.        transport preferred all

C.        transport type all

D.       transport input all

 

Correct Answer: D

 

 

QUESTION 248

Refer to the exhibit. A network technician enters the following line into the router.

 

Tidmore1(config)# access-list 106 deny tcp 192.168.254.0 0.0.0.255 any eq www

 

What is the effect of this configuration?

 

clip_image004

 

A.       The change has no effect on the packets being filtered.

B.        All traffic from the 192.168.254.0 LAN to the Internet is permitted.

C.        Web pages from the Internet cannot be accessed by hosts in the 192.168.254.0 LAN.

D.       No hosts in the 192.168.254.0 LAN except 192.168.254.7 can access web pages from the Internet.

 

Correct Answer: A

 

 

QUESTION 249

Refer to the exhibit. What statement is true of the configuration for this network?

clip_image006

A.         The configuration that is shown provides inadequate outside address space for translation of the number of inside addresses that are supported.

B.          Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support the NAT configuration as shown.

C.          The number 1 referred to in the ip nat inside source command references access-list number 1.

D.         ExternalRouter must be configured with static routes to networks 172.16.1.0/24 and 172.16.2.0/24.

 

Correct Answer: C

 

 

QUESTION 250

Refer to the exhibit. Statements A, B, C, and D of ACL 10 have been entered in the shown order and applied to interface E0 inbound, to prevent all hosts (except those whose addresses are the first and last IP of subnet 172.21.1.128/28) from accessing the network. But as is, the ACL does not restrict anyone from the network. How can the ACL statements be re-arranged so that the system works as intended?

 

clip_image007

 

A.      ACDB

B.      BADC

C.      DBAC

D.      CDBA

 

Correct Answer: D

 

 



Download Latest Cisco 200-101 ICND2 Real Free Tests , help you to pass exam 100%.


Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.